Open as PDF
Scanning Frequency (H)
Scanning Frequency (V)
Total/Effective Pixels No.
Video Output Level
Lens- Mirror Cover
NTSC : 525 Lines PAL : 625 Lines
2 : 1 Interlace
1/3 inch SONY Super HAD CCD
More than 48dB
380 TV Lines
1.0 Vp-p (75 Ohms, composite)
Fixed Lens (f=3.8mm)
1/60~100,000 Sec. 1/50~100,000 Sec.
Power (Red Jack), Video (Yellow Jack)
12VDC (10V~15V), 0.15A / 1.8W (Max)
This manual explains the installation and operating method for the
color dome camera. Before installation, make sure you are familiar
with this product's special features and proper operating technique.
Design and specifications
are subject to change
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
All the warnings and instructions of this manual should be followed.
Keep enough space around the unit for ventilation.
Slots and openings on the monitor should not be blocked.
During flashes of lightning or cracks of thunder, or when the system
is not used for a long time, unplug the system power supply to
protect the unit from lightening or power surges.
Do not attempt to service this unit yourself as opening or removing
covers may you to dangerous voltage or other hazards. Please refer
all servicing to qualified service personnel.
Do not place anything on top of the unit that might spill or fall into it.
To reduce the risk of fire or electric shock, do not expose this appliance
to rain or moisture.
Remove the plug from the outlet before cleaning. Do not use liquid
aerosol detergents. Use water damped cloth for cleaning.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM
OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT
TO RAIN OR MOISTURE"
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance-
(servicing) instructions in the literature accompanying the appliance.
Explanation of two Symbols
Insert coin to the side
hole and remove the
dome cover by twist coin.
The image does not
appear on the screen.
Check the power source for the monitor
and camera and ensure that the voltage
and polarity are properly connected and
being supplied correctly.
The image on the
screen is dim.
Check if the lens is stained. If dirty,
clean the lens with a soft, clean cloth.
Adjust the Back Focus of the lens again.
The camera does not
work properly, the surface
of the camera case is hot,
and a black line appears
on the screen.
Check if you have connected the camera
to a proper power source and If there is
no problem with the power, turn the unit
off immediately and seek assistance from
our Customer Service department.
The screen blinks a lot.
Check if the camera is pointed toward
the sun or a fluorescent lamp.
Adjust the angle or location of the
camera if too much light is coming into
Draw out power/video wires to the connecting
Stick the guide pattern on the wall or ceiling.
Adjust desired focus and scene by turning
and moving the 3-axis camera bracket by
Drill two holes according to the guide pattern
then insert anchors into the drilled holes.
Put the dome cover over the base.
Fix the dome cover on the base by covering.
Fixed the camera to a celling using two screws.
If you have trouble operating
your camera, refer to the following.
If the guidelines do not enable you to solve the problem,
contact an authorized technician.
• The wire is polarized.
• Use 12VDC power source.
12VDC Power Type
Power - 12VDC
bracket makes it much
easier to rotate in any
Rev 0 03
Call 1.800.796.CCTV for sales, service and customer support.
• 1/3” SONY Super HAD CCD
• 380 TV Lines Resolution
• Built-in Fixed Lens (f=3.8mm)
• Min. Illumination : 0.1 Lux
• Auto White Balance
• Diameter of Bubble : 85mm
• Easy Install (3-Axis)
READ AND KEEP THIS