Filter
Top Products
NS-A700PF6 or NS-A700PF6-2 (LG)
1 Press the push button on the lter housing.
2 Gently pull the cartridge down and then pull it out
of the lter housing. You may need to lower or
remove the shelf below the cover.
3 Ensure that o-rings are present on the cartridge
and are seated into grooves.
4 Insert the new cartridge, pushing it in until it stops.
Push up rmly and close the cover.
5 Reset the lter change indicator in your refrigera-
tor, if applicable. (See “RESETTING YOUR FILTER
INDICATOR” on back page.)
Note: Run approximately 1.5 gallons of water through
the new lter before use.
NS-A8001F6 or NS-A8001F6-2 (Maytag, PuriClean II, Amana,
Sears/Kenmore, Whirlpool and Kitchenaid)
1 Twist the old lter counterclockwise and pull it out
of the receiver. The water automatically shuts o.
2 Push the new lter into the lter receiver until it
stops.
3 Turn the new lter clockwise until it stops.
4 Reset the lter change indicator in your refrigerator,
if applicable. (See “RESETTING YOUR FILTER
INDICATOR” on back page.)
Notes:
• Run approximately 1.5 gallons of water through the
new lter before use.
• Do not remove O-ring.
NS-LT600B-2 (LG and Kenmore)
1 Remove the old lter by rotating a half turn
counterclockwise, then pull it out. The water
automatically turns o.
2 If you have a Kenmore refrigerator, check if there is
a plastic or metal cap that covers the top of the old
lter. If there is, pull o the cap and attach it to
your new lter. If there is not, continue to step 3.
3 Align the top of your new lter with the receiver,
then push it in until it stops.
4 Rotate the lter a half turn clockwise to secure the
lter, then twist a little more to prevent leaks.
NS-DA2920 or NS-DA2920-2 (Samsung)
1 Remove the old lter by rotating it a 1/4 turn
counterclockwise, then pull it out.
2 Align the top of your new lter with the receiver,
then push it up until it stops.
3 Rotate the lter a 1/4 turn clockwise to secure the
lter.
BEFORE USING YOUR FILTER
If your refrigerator has a change lter indicator, reset it. See “Resetting your
lter indicator” for instructions.
Quick Setup Guide
|
NS-A700PF6/NS-A700PF6-2/NS-A8001F6/NS-A8001F6-2/NS-LT600B-2/NS-DA2920/NS-DA2920-2
Refrigerator Filter
Before using your new product, please read these instructions to prevent any damage.
Congratulations on your purchase of one of the highest performing
water lters on the market today. Insignia lters use a high-grade
coconut carbon that has 50% more micro-pores than standard
carbon. They also use fewer high-compression binders, giving you the
best water ltration possible.
PACKAGE CONTENTS
• Refrigerator lter(s) (1 or 2 pack)
• Quick Setup Guide
GENERAL INSTALLATION GUIDELINES
1 YOU MUST SOAK your new lter in water for 15 minutes prior to
installing it in your refrigerator. This is needed to remove air from
the carbon block.
2 It is normal for black carbon nes (particles) to appear on the outside
of your lter. This happens when the lter is jarred in shipping, it is
safe, simply wipe it o.
3 Connections on our lters are larger in size to prevent leakage. This
might require more hand leverage to install.
4 After installing, run about two to three gallons of water through your
refrigerator’s water dispenser to remove air and loose carbon pieces.
The water may be cloudy and sputter until the air is removed.
5 We apply a safe, NSF approved, food grade silicone lubricant to our
lter connectors (jelly like substance).
Installation:
*PUSH AND TURN HARD
To remove turn counter-clockwise
To install turn clockwise
Do not remove the O-ring
Filter receivers are designed to be exible.
Don’t worry, they won’t break!
C
M
Y
CM
MY
CY
CMY
K
NS-A700PF6_A700PF6-2_A8001F6_A8001F6-2_LT600B-2_DA2920_DA2920-2_14-1039_QSG_V3_EN.ai 1 9/16/2014 4:29:05 PMNS-A700PF6_A700PF6-2_A8001F6_A8001F6-2_LT600B-2_DA2920_DA2920-2_14-1039_QSG_V3_EN.ai 1 9/16/2014 4:29:05 PM
V3
FINAL
FOR PRINT