JVC ENLYT1127-001A Camcorder User Manual


 
EN
45
TROUBLESHOOTING
The focus does not adjust automatically.
Focus is set to the Manual mode.
¥ Set Focus to the Auto mode ( pg. 30).
The recording was done in a dark place, or the
contrast was low.
The lens is dirty or covered with condensation.
¥ Clean the lens and check the focus again
( pg. 50).
The cassette will not load properly.
The cassette is in the wrong position.
¥ Set it in the right position ( pg. 9).
The battery’s charge is low.
¥ Install a fully charged battery (
pg. 7, 8).
The memory card will not load properly.
The memory card is in the wrong position.
¥ Set it in the right position ( pg. 11).
In the 5-Second mode, recording ends before
5 seconds have elapsed.
•The 5-Second mode is set to “Anim.” in the Menu
Screen.
¥ Select “5S” in the Menu Screen ( pg. 26).
Snapshot mode cannot be used.
The Squeeze mode is selected.
¥ Disengage the Squeeze mode ( pg. 33).
The colour of Snapshot looks strange.
The light source or the subject does not include white.
Or there are various different light sources behind the
subject.
¥ Find a white subject and compose your shot so that
it also appears in the frame ( pg. 17, 29).
The Sepia or Monotone mode is activated.
¥ Turn off Sepia and Monotone ( pg. 27).
The image taken using Snapshot is too dark.
Shooting was performed under backlit conditions.
¥ Press the BACKLIGHT Button w ( pg. 30).
The image taken using Snapshot is too bright.
The subject is too bright.
¥ Set “PROGRAM AE” to “SPOTLIGHT” in the Menu
Screen ( pg. 27).
Digital Zoom does not work.
10X*/16X** optical zoom is selected.
¥ Set “ZOOM” to “40X” or “500X*/700X**” in the Menu
Screen ( pg. 32).
•The VIDEO/MEMORY Switch t is set to “MEMORY”.
¥ Set the VIDEO/MEMORY Switch t to “VIDEO”
( pg. 13).
* GR-DX300 only.
**GR-DX95/DX75 only.
Before consulting your JVC dealer, please check the
following to see it you can correct the problem yourself.
The camcorder is a microcomputer-controlled
device. External noise and interference (from a TV,
a radio, etc.) might prevent it from functioning
properly. In such cases, first disconnect its power
supply unit (battery pack, AC Adapter, etc.) and wait
a few minutes; and then re-connect it and proceed
as usual from the beginning.
No power is supplied.
The power is not connected properly.
¥ Connect the AC Adapter securely ( pg. 7).
The battery is dead.
¥ Replace the dead battery with a fully charged one
( pg. 7, 8).
“SET DATE/TIME!” appears.
The date/time is not set.
¥ Set the date/time ( pg. 10).
The built-in clock’s rechargeable lithium battery is
discharged.
The previously set date/time is erased.
¥ Connect the camcorder to an AC outlet using the AC
Adapter for over 24 hours to charge the clock’s
lithium battery ( pg. 49).
Recording cannot be performed.
—— For Tape Recording ——
The tape’s erase protection tab is set to “SAVE”.
¥ Set the tape’s erase protection tab to “REC”
( pg. 9).
•The Power Switch @ is set to “ ” or “OFF”.
¥ Set the Power Switch @ to “ ” or “ ” ( pg. 13).
•The VIDEO/MEMORY Switch t is set to “MEMORY”.
¥ Set the VIDEO/MEMORY Switch t to “VIDEO”.
•“TAPE END” appears.
¥ Replace with new cassette ( pg. 9).
The cassette holder cover is open.
¥ Close the cassette holder cover.
—— For Memory Card Recording ——
•The VIDEO/MEMORY Switch t is set to “VIDEO”.
¥ Set the VIDEO/MEMORY Switch t to “MEMORY”.
There is no picture.
The camcorder is not getting power, or some other
malfunction exists.
¥ Turn the camcorder’s power off and on again
( pg. 13).