Filter
Top Products
INSTR,CODE SET,DR4
Linear P/N: 200868 F
Size: 8.500" X 11.000"
Material: 20 Lb. Mead Bond
Ink: Black
Scale: 1-1
DR4V
DR4-12
DIGITAL
RECEIVER
Code Setting
Instructions
(800) 421-1587 • www.linearcorp.com
DESCRIPTION
The Delta-3 DR4V & DR4-12 digital receivers are
four-channel wireless radio controls designed for use with
automatic garage/gate operators and access control systems. The
receivers can be activated by any of the Delta-3 format
transmitters. Receivers must be mounted at least 8 feet apart.
The Delta-3 radio format provides 256 different digital codes. The
codes are set using the 8-position coding switches in the units.
✶
CAUTION: All transmitters and receivers should be
recoded by the installer prior to operation.
In order to avoid the possibility of duplicating codes in adjacent
systems, factory set codes should not be used. In addition, among
the valid codes available, four others should not be used. These
include: all keys set ON or OFF and keys set alternating ON/OFF.
Activate each transmitter to test the equipment.
☞
WARNING! BE SURE DOOR OR GATE
AREAS ARE CLEAR OF OBSTRUCTIONS
STEP 1
Locate coding switch.
Locate the digital coding switch
which is recessed in the center of the back of the receiver case.
Note that the coding switch has eight keys. The keys are numbered
1 through 8. Key No. 1 and Key No. 2 are not used for coding the
receiver; their functions are permanently wired on the circuit
board.
STEP 2
Code the receiver.
Pick any combination of ON/ OFF
codes and set them on switch keys 3 through 8. Ignore Keys 1 and
2. The ON position is when the top of the switch is down. The OFF
position is when the top of the switch is up and the bottom is down.
The code set on Keys 3 through 8 on the receiver must now be
matched by all transmitters used in the system.
STEP 3
Code the transmitters.
Remove the battery access door
located on the back of the transmitter case to set transmitter codes.
Transmitter keys 1 and 2 determine which channel the transmitter
will activate. Keys 3 through 8 must match keys 3 through 8 on
the receiver. Refer to transmitter code set instructions to code
multi-button transmitters.
STEP 4A
Connecting receiver (using transformer power).
A
Model T12A (used with DR4-12) or 524 (used with DR4-V)
transformer can be used to power the receiver when connecting
receiver to any operator. Connect as shown, then plug the
transformer into a convenient (unswitched) 120 VAC outlet.
STEP 4B
Connecting receiver (using operator power).
Connect the receiver to the garage door or gate operator as shown
in the diagram. Power will be supplied from the operator.
STEP 5
Connecting receiver to 3-button commercial operator.
Connect normally open outputs to up and down inputs. Connect
normally closed output in series with the stop output. Connect
receiver power input to operator radio power or transformer
.
LINEAR LIMITED WARRANTY
This product is warranted to the consumer against defects in material and workmanship for one year from the
date of purchase. This warranty applies to first retail buyers of new devices. Warrantor will repair, or at its option,
replace, any device it finds that requires service under this warranty, and will return the repaired or replaced
device to the consumer at the warrantor’s cost. For warranty service and shipping instructions contact warrantor
at the address shown below. Devices must be sent to warrantor for service at owner’s expense. The remedies
provided by this warranty are exclusive. Implied warranties under state law are to the one year period of this
written warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. In order to be protected by this warranty, save your proof of purchase and send
copy with equipment should repair be required. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
All products returned for warranty service require a Return Product Authorization Number (RPA#).
Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless
signaling. However, there are some limitations which must be observed.
✶
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15
devices. As such, they have limited transmitter power and therefore limited range.
✶
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals
that occur on or near their operating frequencies, regardless of code settings.
✶
Changes or modifications to the device may void FCC compliance.
✶
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
✶
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
dealer, and these facts should be communicated to the ultimate users.
This device complies with FCC Rules Part 15 and IC Canada Rules and Regulations. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Copyright © 1999 Linear Corporation 200868 F
RECEIVER
CODING SWITCH
POWER INPUT
WHITE/WHITE
DR4V:
24 VOLTS AC/DC
DR4-12:
12 VOLTS AC/DC
12 CONDUCTOR
RIBBON. CHANNEL 1
STARTS THIS END
Ch. 1
Ch. 2
Ch. 3
Ch. 4
Brown N/O
Red Com.
Orange N/C
Yellow N/O
Green Com.
Blue N/C
Violet N/O
Grey Com.
White N/C
Black N/O
Brown Com.
Red N/C
DR-4 CODING
SWITCH
SET KEYS 3-8
TO ANY CODE
KEYS 1 & 2
ARE UNUSED
MATCH
3-8
MATCH
3-8
MATCH
3-8
1 & 2
OFF
1 ON
2 OFF
1 & 2
ON
TRIGGERS CH. 1
TRIGGERS CH. 2
TRIGGERS CH. 3
TRIGGERS CH. 4
TRANSMITTER
#1
TRANSMITTER
#3
TRANSMITTER
#2
TRANSMITTER
#4
MATCH
3-8
1 OFF
2 ON
MANUAL
PUSHBUTTON
GARAGE DOOR
OPERATOR
TRANSFORMER
DR4V: #524
DR4-12: #T12A
RADIO
RECEIVER
BROWN
RED
CONNECT OTHER
RECEIVER OUTPUTS
TO ADDITIONAL
OPERATORS
OPEN
CLOSE
STOP
CHANNEL 1
CHANNEL 3
CHANNEL 2
OPEN
CLOSE
STOP
GREEN
BLUE
WHITE
YELLOW
VIOLET
ORANGE
GRAY
GREEN
RED
1
2
3
6
DR-4
RECEIVER
RECEIVER POWER
WALL STATION
OPERATOR
X
RED
Splice Red
wire to Red
X
RED
Splice Orange
wire to Red
3 Radio Pwr
1 Common
2 Relay
OPERATOR
MANUAL
PUSHBUTTON
RADIO POWER
RADIO
RECEIVER
BROWN
RED
WHITE
WHITE
CONNECT OTHER
RECEIVER OUTPUTS TO
ADDITIONAL OPERATORS
NOTE: OPERATOR
MUST SUPPLY
12 VOLTS AC/DC - DR4-12
24 VOLTS AC/DC - DR4V