Filter
Top Products
50
4-7-2 Viewfinder screen status display
configuration
All the items that can be displayed are laid out inside the
viewfinder as shown in the figure below.
4-7-3 Selecting the viewfinder screen
display items
To select which items are to be displayed on the viewfinder
screen, perform menu operations to open the <VF
INDICATOR1> screen or <VF INDICATOR2> screen from
the VF page, and select ON or OFF for the display or select
the type desired for each item concerned.
For details on operation, refer to “4-6-2 Basic menu
operations.”
#
< VF INDICATOR1 >
EXTENDER :ON
SHUTTER :ON
FILTER :ON
WHITE :ON
GAIN :ON
IRIS :S+IRIS
CAMERA ID :BAR
ID POSITION :UPPER L
DATE/TIME :OFF
ZOOM LVL :ON
COLOR TEMP :ON
SYSTEM MODE :ON
CAMERA MODE :ON
#
< VF INDICATOR2 >
TAPE :ON
BATTERY :ON
AUDIO LVL :ON
TC :OFF
VTR WARNING :NORMAL
SAVE LED :SAVE
For details, refer to the following pages.
4-7 Viewfinder screen status
displays
Not only the images but the lamps and characters indicating
the unit’s settings and operation statuses as well as the
messages, center and safety zone markers, camera ID and
other information are displayed inside the viewfinder.
4-7-1 Viewfinder lamp displays
Viewfinder pictured here is the AJ-
HVF21G.
(For details concerning viewfinder,
refer to the operating instructions
of each viewfinder.)
1 TALLY/REC (recording) lamp
This lights up (red) during recording. It flashes when a
problem has occurred. For details, refer to the
appropriate section in “6-3 Warning system.”
2 (abnormal operating status warning) lamp
This lights when the unit is set to an abnormal operating
status for any of the items set to “ON” on the “!LED”
screen of the setting menu.
For details on selecting the items which are to be
indicated with the lamp, refer to the <!LED> screen
items in “Chapter 7 Menu description tables.”
3 BATT (battery) lamp
This starts flashing when the battery voltage has dropped
to the level where the battery will no longer be usable in
several minutes’ time, and it lights when the battery is no
longer usable. To prevent operation from being
interrupted, replace the battery before it has discharged
completely. For details, refer to the appropriate section in
“6-3 Warning system.”
4 SAVE (VTR power-saving) lamp
This lights when the VTR SAVE/STBY switch is set to
SAVE. It goes off during recording.
<Note>
In the rec-pause mode, the SAVE mode is established
automatically, and the lamp lights after the time set for the
pause timer (temporary stop time) has elapsed.
After two minutes in the play-pause mode, the SAVE
mode is established automatically, and the lamp lights.
TALLY / REC
BATT
SAVE
1
432
Chapter 4 Adjustments and settings for recording
(continued)
/34min DIONIC90
-- GAIN -- -- USER SW GAIN --
LOW : 0 S.GAIN:30/36
MID :12
HIGH:18 DS.GAIN: 6 /10 /12
/15 /20
UM:S.GAIN 30
dB
U1:AUDIO CH1 U2:DS.GAIN 12
REC WARNING COMP
EX
TCG 00:00:00:00 iREC
3.2K 12 M F:1---- ---+ BS 23h59m
1A A 18
dB
F:2---- ---+ ++F5.6 Z99
:
:
∫
∫
:
:
:
24PA 3
1/
249.8 ∑10min REC14.6V
1080 DRS
:
:
2
1
9
:
;
<
=
>
C
D
8
7
K
M
J
3
4L
? B E F GH IA@
5 6