Filter
Top Products
Item/
(display mode)
Description of settings
1394 UB REGEN
(VCR)
For selecting the user’s bit to be recorded
when recording the signals of the
component connected to the DV connector.
OFF:
The user’s bit selected for the UB MODE
item is used for the recording.
ON:
The user’s bit of the signals input to the
DV connector is used for the recording.
OWhen ON has been selected as this
item’s setting, this setting takes
precedence over the UB MODE item
setting.
OThe user’s bit is not recorded if the
signals do not contain the user’s bit
information.
OWhen no signals are supplied to the DV
connector, the UB MODE item setting is
followed.
RECORDING SETUP screen
Item/
(display mode)
Description of settings
REC SPEED
(Camera)
(VCR)
For selecting the recording time mode.
SP
:
SP (standard play) mode
LP :
LP (long play) mode
AUDIO REC
(Camera)
(VCR)
For selecting the system for converting the
recording to PCM audio.
12 bit :
12-bit/32kHz
16 bit :
16-bit/48kHz
TC MODE
(Camera)
(VCR)
For selecting the time code correction
mode in which the time code of the internal
time code generator is to be recorded.
DF :
The drop frame mode is used.
NDF :
The non-drop frame mode is used.
OWhen the progressive mode has been
set to 24P or 24P (ADV), the non-drop
frame mode is established regardless of
this item’s setting.
TCG
(Camera)
(VCR)
For setting the operation mode in which the
internal time code generator is to be run.
FREE RUN:
The internal time code generator is run
regardless of the operation mode.
REC RUN
:
The internal time code generator is run
during recording.
FIRST REC TC
(Camera)
(VCR)
For selecting the time code which is to be
recorded when recording is started.
REGEN:
Recording proceeds in such a way that
the time code continues on (is
regenerated) from the time code on the
tape.
PRESET:
The time code is not regenerated from
the time code on the tape.
The time code is recorded using the
value set in the TC PRESET item
serving as the initial value.
However, the time code is forcibly
regenerated when shooting with frame-
to-frame continuity has been performed.
TC PRESET
(Camera)
(VCR)
For setting the initial value of the time code
to be recorded.
This item’s setting is valid when PRESET
has been selected as the setting for the
FIRST REC TC item.
OWhen the progressive mode has been
set to 24P or 24P (ADV), set the frame
value to 0 or to a multiple of 5. If any
other value is set, the time code
recorded will shift.
MIC ALC
(Camera)
For setting the mic level automatic control
function to ON or OFF.
OFF ON
Audio distortion caused by excessively high
input level can be minimized by selecting
ON for this item.
OThe recording level of the audio signals
must be adjusted using the AUDIO
controls, irrespective of this setting.
1394 TC REGEN
(VCR)
For selecting the time code to be recorded
when recording the signals of a component
connected to the DV connector.
OFF:
The signals are recorded using the time
code which was set using the TC MODE
item, TCG item and FIRST REC TC
item.
ON:
The signals are recorded using the time
code of the signals which have been
input to the DV connector.
OWhen ON has been selected as this
item’s setting, this setting takes
precedence over the TC MODE item,
TCG item and FIRST REC TC item
settings.
OWhen no signals are supplied to the DV
connector, the TC MODE item, TCG item
and FIRST REC TC item settings are
followed.
MIC GAIN 1
(Camera)
For setting the input level of the external
microphone which is connected to the
INPUT 1 connector.
-
50 dB
-
60 dB
MIC GAIN 2
(Camera)
For setting the input level of the external
microphone which is connected to the
INPUT 2 connector.
-
50 dB
-
60 dB
43
Setting menus
The underlining indicates the factory setting.