Filter
Top Products
133
Menu List
Appendix
MEM Menu
WIPE Menu
To store a wipe pattern in the direct wipe number (menu page 510)
Select a wipe pattern on menu page 510, turn the F3 control to display the direct wipe number (0 to 9)
under DRCT NO., then press the F4 control (PRESET).
To recall the preset wipe pattern
When you turn the F3 control to display Wipe under DIRECT in SW mode, WIPE: is displayed at the
lower left corner on the display panel. (If DIRECT is not displayed on the display panel above the F3
control, press the F3 control once to display it.)
Setting menu Setting item Description
400 FREEZE.. 410 SIGNAL IN 1, IN 2, IN 3, IN 4, IN 5, IN 6,
IN 7, IN 8, IN 9, FM 1, FM 2,
MAT1, MAT2, CLBR, PGM, PVW
Allows you to register a still image in frame
memory 1 or 2.
Turn the F1 control to select a signal then turn the
F2 control to specify FM1 or FM2. Press the F3
control to register the image.
DIST FM 1, FM 2
FREEZE
Exec
MODE.. 420 FM 1 Frame, Field1, Field2 Sets up the signal imported to FM 1 or FM 2 as a
still image.
Setting FOLDER to AutoSwap automatically
swaps between the data in FM 1 and FM 2 after
importing the data.
FM 2 Frame, Field1, Field2
FOLDER Separate, AutoSwap
NV MEM.. 430 LOAD
NOP, FM 1, FM 2, Both
Stores still image data in nonvolatile memory and
recalls them.
LOAD: Writes the data in nonvolatile memory to
FM 1 or FM 2. (When the switcher is on, data
are written automatically.)
STORE: Stores still image data of FM 1 or FM 2 in
internal nonvolatile memory. It takes about 3
minutes to store one frame memory.
STORE
NOP, FM 1, FM 2, Both
TIME.. 440 MM/DD/YY 01/01’09 Enter the date and time when the data are stored
in a computer.
Press the F1 control to highlight the date then turn
the F1 control to change the date. To move the
highlighted position, turn the F2 control.
In the same manner as above, change the time
using the F3 and F4 controls. To register the
settings, press the F4 control.
Note
The switcher does not have a built-in clock. The
entered date and time will not be updated.
<=>
HH:MM:SS 00:00:00
<=>
Set
Setting menu Setting item Description
500 PATTERN.. 510 NUMBER 000, 001, 002, 003, 004, 005, 021,
022, 023, 028, 029, 031, 040, 051,
057, 058, 074, 082, 096, 098
Turn the F1 or F2 control to select a wipe pattern.
Storing it in the direct wipe number is supported.
For details, see “To store a wipe pattern in the
direct wipe number (menu page 510)” on page
133.
(Figure) (Wipe pattern figure)
DRCT NO. None, 0 to 9
PRESET
Exec
BORDER.. 520 LUM 0.0 to 100.0 (in 0.1) Set the border between the videos for a wipe.
Turn the F1 to F4 controls to adjust LUM
(luminance), SAT (saturation), HUE, and WIDTH
of the border.
All items except WIDTH can be set using the
joystick.
SAT 0.0 to 100.0 (in 0.1)
HUE 0.0 to 359.5 (in 0.5)
WIDTH Off, 1 to 50 (in 1)