Filter
Top Products
3287508010
3-287-508-01 (1)
安全のための注意事項を守る。
故障したり破損したら使わずに、ソニーのサービス窓口に相談する。
Operating Instructions
お買い上げいただきありがとうございます。
XCD-V60CR/SX90CR/U100CR
(Color model)
XCD-V60/SX90/U100
(Black and white model)
2007 Sony Corporation
Printed in Japan
警告表示の意味
注意を促す記号
行為を禁止する記号
行為を指示する記号
下記の注意を守らないと、 や 、
により や につながること
があります。
設置は確実に
1
レンズは確実に取り付ける
1
下記の注意事項を守らないと、 をしたり周辺の物品に
を与えることがあります。
内部に水や異物を入れない
DC
分解しない、改造しない
カメラケーブルを傷つけない
指定された専用機器に接続する
指定された接続ケーブルを使う
Owner’s Record
The model and serial numbers are located on the bottom. Record the
serial number in the space provided below. Refer to these numbers
whenever you call upon your Sony dealer regarding this product.
Model No. _____________ Serial No. ______________
WARNING
To reduce the risk of re or electric shock, do not
expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualied personnel only.
IMPORTANT
The nameplate is located on the bottom.
Power Supply
The unit must always be operated with a 12V DC class 2 power supply.
In the USA, use a power supply which is UL Listed.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
You are cautioned that any changes or modications not expressly
approved in this manual could void your authority to operate this
equipment.
All interface cables used to connect peripherals must be shielded in
order to comply with the limits for a digital device pursuant to Subpart
B of Part 15 of FCC Rules.
For customers in Europe
This camera is not intended for use in security applications in the
meaning of the European standard series EN 50132 (Alarm systems -
CCTV surveillance systems for use in security applications).
For the customers in Europe
The manufacturer of this product is Sony Corporation, 1-7-1 Konan,
Minato-ku, Tokyo, Japan.
The Authorized Representative for EMC and product safety is Sony
Deutschland GmbH, Hedelnger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to the addresses
given in separate service or guarantee documents.
This apparatus shall not be used in the residential area.
日本語
A
-1
基本構成／
-2
オプションの構成
IEEE1394b
12 I/O
PC
DC-700
電源について
PC IEEE1394b
DC-700
使用・保管場所
0 40
お手入れ
XCD-V60CR/SX90CR/U100CR RAW
XCD-V60/SX90/U100
IEEE1394b
端子
800Mbps IEEE1394b 2
高画質
CCD
XCD-V60CR/V60 VGA 33 CCD 90
XCD-SX90CR/SX90 SXGA 125 CCD
30 XCD-U100CR/U100
UXGA 200 CCD 15
CCD
外部トリガー機能
電子シャッター
12
ピン
I/O
コネクター端子
IEEE1394b 12
12
I/O
低消費電力
XCD-V60CR/V60/SX90CR/SX90 2.8W DC 12V
XCD-U100CR/U100 3.0W DC 12V
筐体固定
CCD
CCD
CCD Charge Coupled Device
白点
CCD
CCD
スミア現象
折り返しひずみ
B
(
)
カメラモジュール
CCD
IEEE1394b
カメラケーブル（市販）
IEEE1394b
C
マウントレンズ（市販）
カメラ用画像入力ボード（市販）
PC PCI
IEEE1394
800Mbps IEEE1394b
三脚アダプター
VCT-ST70I
（ソニー製）
カメラアダプター
DC-700
（ソニー製）
AC
カメラケーブル
CCXC-12P02N
（
2 m
）
/05N
（
5 m
）
/10N
（
10 m
）
/25N
（
25 m
）（ソニー製）
12 I/O
C
レンズマウント（
C
マウント
)
C
ご注意
C 10mm
10mm
カメラ固定用補助穴（上面）
カメラ固定用基準穴（底面）
4
4 VCT-
ST70I
English
When Installing the Camera Fig. A
When you install the camera with various peripheral devices and if the devices
have dierent ground electric potential, ground only one device. In case there
is an ground electric potential dierence, the camera may be damaged.
-1
Basic conguration /
-2
Optional conguration
IEEE1394b connector
12-pin I/O connector
Host device (e.g., PC)
Abnormal electricity
Ground electric potencial dierence
Power supply unit (DC-700/700CE)
Notes on Operation
Power supply
Power is supplied to the camera module via the IEEE1394b cable connected to a
PC. If the power supply is insucient, use the DC-700/700CE that supplies stable
power with less ripple or noise.
Foreign bodies
Be careful not to spill liquids, or drop any ammable or metal objects in the
camera body.
Locations for operation and storage
Avoid operation or storage in the following places.
Extremely hot or cold locations. Recommended temperature range is 0°C to
40°C (32°F to 104°F)
Locations subject to strong vibration or shock
Near generators of strong electromagnetic radiation such as TV or radio
transmitters
Care
Use a blower to remove dust from the surface of the lens or optical lter. Clean
the exterior with a soft, dry cloth.
If the camera is very grimy, apply a cloth soaked in a mild detergent then wipe
with a dry cloth. Do not apply organic solvents such as alcohol which may
damage the nish.
Overview
The XCD-V60CR/SX90CR/U100CR is a color digital camera module that outputs
RGB Raw Data. The XCD-V60/SX90/U100 is a monochrome digital camera
module.
IEEE1394b connector
The camera module can output a digital image with a transfer speed of
800 Mbps. Two IEEE1394b connectors allow you to make up a daisy chain
connection.
High resolution
The camera module uses a progressive scan CCD and produces high-resolution
and high-speed image output.
The XCD-V60CR/V60 has a CCD of 330,000 pixels (VGA) and outputs a digital
image at 90 frames per second. The XCD-SX90CR/SX90 has a CCD of 1,250,000
pixels (SXGA) and outputs at 30 frames per second. The XCD-U100CR/U100 has
a CCD of 2,000,000 pixels (UXGA) and outputs at 15 frames per second.
Because the CCDs are square pixel CCDs, you don’t need to convert the aspect
ratio in your image processing.
External trigger function
You can operate the shutter at any timing by synchronizing the shutter with the
external trigger signals.
Electronic shutter
You can select the exposure time from a variety of settings. This allows you to
capture an image under optimal conditions.
12-pin I/O connector
When power from the IEEE1394b connector is insucient, power is supplied
through the 12-pin connector. The 12-pin connector is also used for a trigger
input and strobe output, and as a general-purpose I/O port.
Low power consumption
The power consumption is decreased to 2.8 W for the XCD-V60CR/V60/SX90CR/
SX90 or 3.0 W for the XCD-U100CR/U100, with 12 V DC input.
Body xing
The mounting screw holes are provided in the reference plane on the lower
surface of the body, allowing mounting with the absolute minimum deviation
of the optical axis.
Phenomena Specic to CCD Image Sensors
The following phenomena that may appear in images are specic to CCD (Charge
Coupled Device) image sensors. They do not indicate malfunctions.
White ecks
Although the CCD image sensors are produced with high-precision
technologies, ne white ecks may be generated on the screen in rare cases,
caused by cosmic rays, etc.
This is related to the principle of CCD image sensors and is not a malfunction.
The white ecks especially tend to be seen in the following cases:
when operating at a high environmental temperature
when you have raised the gain (sensitivity)
when using the slow shutter
Vertical smear
When an extremely bright object, such as a strong spotlight or ashlight, is
being shot, vertical tails may be produced on the screen, or the image may be
distorted.
Monitor screen Vertical tails shown
on the image
Bright object
(e.g. strong spotlight,
strong reected light,
ashlight, the sun)
Aliasing
When ne patterns, stripes, or lines are shot, they may appear jagged or icker.
System Components Fig. B
The camera module imaging system comprises the following products.
Products
to
are used for the basic conguration, and
to
for the
optional conguration. (All the products except the camera module are
available separately.)
Camera module
This is a small-size, high-resolution, camera module using a CCD image sensor.
IEEE1394b camera cable (commercially available)
Connect this cable to the IEEE1394b connector on the rear panel of the camera
module. The power and image/control signals are transmitted through this
cable. To prevent a poor connection or damage to the camera or cable, use the
cable equipped with xing screws.
C-mount lens (commercially available)
Use an appropriate lens for the camera module and usage.
Camera module interface board (commercially available)
Install the board in a PCI bus slot of a host device such as a PC.
Select an IEEE1394 interface board to match your system.
Select an IEEE1394b interface board if you use the transfer speed of 800 Mbps.
VCT-ST70I tripod adaptor (Sony)
Attach this adaptor to the bottom of the camera module to x the camera
module to a tripod.
DC-700/700CE camera adaptor (Sony)
Connect this adaptor to the camera module to enable power supply from an
ordinary AC power source.
CCXC-12P02N (2 m, 6.6 ft)/05N (5 m, 16.4 ft)/10N (10 m, 32.8 ft)/
25N (25 m, 82 ft) camera cable (Sony)
Connect this cable to the 12-pin I/O connector on the rear panel of the camera
module. The cable is used for power supply and exchange of trigger signals.
Location and Function of Parts and Operation
Front/Top/Bottom
Fig. C
Lens mount (C-mount)
Attach any C-mount lens or other optical equipment.
Note
The lens must not project more than 10 mm (13/32 inch) from the lens mount.
Lens mount face
10 mm (13/32 inch) or less
Auxiliary holes (top)
Reference holes (bottom)
These precision screw holes are for locking the camera module. Locking the
camera module into these holes secures the optical axis alignment.
For details, refer to the Technical Manual.
Four screw reference holes
can be used as the tripod adapor screw holes,
too. Screw the VCT-ST70I tripod adaptor into the four screw holes when you use
a tripod.
(continued on the reverse side)
Digital Camera Module
/ Camera
–1
–2
/ Camera