Filter
Top Products
6
DESCRIPTION
The TC700 Series AutoDome™ systems are quiet,
lightweight, and discreet surveillance dome systems
containing high sensitivity 1/3-inch image format full
performance monochrome or color CCD cameras with a
10:1 auto-iris, auto-focus zoom lens, a high-speed
pan/tilt, and an intelligent, integral receiver/driver. The
one-piece camera, lens, pan/tilt, and receiver/driver
module is housed in a domed enclosure. They are
available in suspended ceiling, hard ceiling recessed,
surface, and pendant mount models. Pendant mount
models are available for indoor or outdoor applications.
INSTALLATION
Attention: Installation should be performed
by qualified service personnel only in
accordance with the National Electrical Code
or applicable local codes.
Attention: L'installation doit être effectuée
uniquement par du personnel de service
qualifié conformément à la réglementation du
Code Electrique National ou à la
réglementation locale.
Achtung! Die Installation sollte nur von
qualifiziertem Kundendienstpersonal gemäß
jeweilig zutreffender Elektrovorschriften aus-
geführt werden.
Atención: La instalación de este equipo debe
ser realizada por personal capacitado, solo
en acuerdo, y en cumplimiento de normas
del "National Electric Code" (Código
Eléctrico Nacional) ó las normas del
Gobierno Nacional Local.
Removing Module From Carton
Refer to
ILLUSTRATIONS
for component description.
CAUTION: Keep in foil bag until grounded at
unit. Be sure to observe all safety measures
for static control when working with this unit
while out of its enclosure. Otherwise, static
damage may result.
For removal from foil bag and installation instructions,
see
TC700 Series - Camera, Lens, Pan/Tilt, and
Receiver/Driver Modules Installation
under
INSTALLATION
in the
Installation and Operating
Instructions
supplied with the particular Backbox
Module ordered.
CAUTION: Do not handle the unit by the
circuit board because this may result in
physical damage to the unit.
OPERATION
Camera Control
These units, as shipped, are factory adjusted as
described below:
Line-lock mode enabled with zero degree phase
delay.
AGC on.
Backlight compensation off.
Electronic shutter off.
Automatic white balance on (color cameras only).
Changing Operating Modes
The AutoDome unit operating modes can be changed
using either a TC8135B Series Controller/Follower or an
Allegiant series keyboard. An Allegiant series keyboard
is required to take full advantage of all the various
features available. See
Camera Commands
for
description of various camera operating adjustments.
AutoDome Commands
Receiver/Driver - Using Auxiliary Controls
Receiver/Driver
Function
Aux
No.
Description On/Off Notes
Scan 1 Auto-pan without
limits
On/off 5
Auto-Pan 2 Auto-pan between
limits
On/off --
Pre-Position Tour 8 -- On/off --
Set Scan/auto-pan
speed
14 -- Inc/dec 2
Set tour period 15 Sets pause between
tour callups
Inc/dec 2
Auto-Speed 16 Enables/disables
auto-speed
On/off 2
Lens - Using Auxiliary Controls
Lens
Function
Aux
No.
Description On/Off Notes
Iris Control 3 -- Auto/
manual
1
Focus Control 4 -- Auto/
manual
1
Auto-iris ALC adj 10 -- Peak/ave 1
Auto-iris Level adj 11 -- Inc/dec 1
Auto-focus
Activation
12 Activates AF upon
movement
On/off 2
Auto-iris Activation 13 Activates AI upon
movement
On/off 2
Auto-Speed (AUX 16)
Auto-speed On:
Issuing this command provides
variable pan speed when unit is operated from a fixed
speed location. The pan speed starts slowly and
increases as the pan control is held on. The speed
resets to slow when the pan control is released. Note:
DIP Switch S2005.4 must be in the OFF position to use
this command; see DIP Switch Settings in the applicable
Installation and Operating Instructions
for additional
information.