Filter
Top Products
8
USING YOUR DYSON APPLIANCE
PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
OPERATION
• Ensure the appliance remains upright in use. Dirt and debris may be released if
it is turned upside down.
• Do not operate while checking for blockages.
• For domestic indoor and car use only. Do not use it whilst the car is in motion or
while driving.
• This product has carbon fibre brushes. Take care if coming into contact with
them. They may cause minor skin irritation. Wash your hands after handling
the brushes.
• To watch a short online video visit:
www.dyson.com.au/dc44gettingstarted
www.dyson.co.nz/dc44gettingstarted
CARPETS OR HARD FLOORS
• Consult your flooring manufacturer’s recommended instructions before
vacuuming and caring for your flooring, rugs, and carpet.
The brush bar on the Dyson vacuum cleaner can damage certain carpet
types and floors.
• Some carpets will fuzz if a rotating brush bar is used when vacuuming. If this
happens, we recommend vacuuming without the motorhead and consulting with
your flooring manufacturer.
• Before vacuuming highly polished floors, such as wood or lino, first check that
the underside of the floor tool and its brushes are free from foreign objects that
could cause marking.
DOCKING STATION INSTALLATION
Use appropriate mounting hardware for your wall type and ensure that the
docking station is mounted securely. Ensure no pipe work (gas, water, air) or
electrical cables, wires or ductwork are located directly behind the mounting
area. The docking station must be mounted in accordance with regulations
and applicable codes/standards (state and local laws may apply). Dyson
recommends the use of protective clothing, eyeware and materials as necessary.
LOOKING AFTER YOUR DYSON APPLIANCE
• Do not carry out any maintenance or repair work other than that shown in this
Dyson Operating Manual, or advised by the Dyson Customer Care Helpline.
• Only use parts recommended by Dyson. If you do not this could invalidate your
Dyson guarantee.
• Store the appliance indoors. Do not use or store it below 0°C. Ensure the
appliance is at room temperature before operating.
• Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning
agents, polishes or air fresheners on any part of the appliance.
VACUUMING
• Do not use without the clear bin and filter in place.
• Fine dirt such as plaster dust or flour should only be vacuumed in very small
amounts.
• Do not use the appliance to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the appliance.
• When vacuuming, certain carpets may generate small static charges in the
clear bin or nozzle. These are harmless and are not associated with the mains
electricity supply. To minimise any effect from this, do not put your hand or
insert any object into the clear bin unless you have first emptied it and cleaned it
with a damp cloth (see ‘Cleaning the clear bin’ on page5).
• Use extra care when cleaning on stairs.
• Do not rest the appliance on chairs, tables, etc.
• Do not press down on the nozzle with excessive force when using the appliance
as this may cause damage.
• Do not leave the cleaner head in one place on delicate floors.
• On waxed floors the movement of the cleaner head may create an uneven
lustre. If this happens, wipe with a damp cloth, polish the area with wax, and
wait for it to dry.
DIAGNOSTICS –APPLIANCE
Less than one minute of charge remaining/fully discharged.
Too cold/too hot - do not use.
EMPTYING THE CLEAR BIN
• Ensure the appliance is disconnected from the charger before emptying the
clear bin.
• Be careful not to pull the ‘ON’ trigger.
• To make emptying the clear bin easier, it is advisable to remove the wand and
motorised floor tool.
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• To release the dirt, push the red button at the side of the clear bin as shown on
page4.
• To minimise dust/allergen contact when emptying, encase the clear bin tightly
in a plastic bag and empty. Remove the clear bin carefully and seal bag tightly,
dispose as normal.
• Do not use without the clear bin in place.
CLEANING THE CLEAR BIN
• Ensure the appliance is disconnected from the charger before removing the
clear bin.
• Be careful not to pull the ‘ON’ trigger.
• Remove the wand and floor tool.
• To remove the clear bin, push the red button at the side of the clear bin as you
would when emptying the clear bin. This will expose the red release button on
the underside of the handle. Press this to release the clear bin as shown on
page6.
• Remove the clear bin carefully.
• Clean the clear bin with a damp cloth only.
• Ensure the clear bin is completely dry before replacing.
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Do not put the clear bin in a dishwasher.
• Clean the cyclone shroud with a dry cloth or dry brush to remove lint and dust.
• To replace the clear bin, fit the tab on the rim of the cyclone shroud into the
aperture on the inside of the top of the clear bin. Push the clean bin up and in.
It will click into place.
• Close the base of the clear bin.
WASHING YOUR FILTER
• Ensure the appliance is disconnected from the charger before removing the
filter.
• Be careful not to pull the ‘ON’ trigger.
• Your appliance has one washable filter, located as shown.
• Press the ‘Filter’ button so you can remove the cyclone and clear bin unit.
• Check and wash the filter regularly according to instructions to maintain
performance.
• The filter may require more frequent washing if vacuuming fine dust or if used
mainly in ‘HIGH CONSTANT SUCTION’ mode.
• Wash the filter with cold water only. Do not use detergents.
• Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
IMPORTANT: After washing please leave at least 12 hours to dry completely
before refitting.
• Place the dry filter into the recess of the handle.
• Fit the base of the handle into the aperture on the base of the cyclone and clear
bin unit. Push both halves together until the ‘Filter’ button engages and locks
into place as shown on page 7.
• To watch a short online video visit:
www.dyson.com.au/dc44filterwash
www.dyson.co.nz/dc44filterwash
LOOKING FOR BLOCKAGES
• Ensure the appliance is disconnected from the charger before looking for
blockages.
• Do not operate while checking for blockages. Failure to do so could result in
personal injury.
• Beware of sharp objects when checking for blockages.
• Refit all parts securely before using.
• Clearing blockages is not covered by your Dyson guarantee.
• If you cannot clear an obstruction you may need to remove the brush bar. Use
a coin to unlock the fastener marked with a padlock. Remove the obstruction.
Replace the brush bar and secure it by locking the fastener. Ensure it is fixed
firmly before operating the appliance.
• This product has carbon fibre brushes. Take care if coming into contact
with them, as they may cause minor skin irritation. Wash your hands after
handling the brushes.
CLEARING BLOCKAGES – THERMAL CUT-OUT
• This appliance is fitted with an automatically resetting thermal cut-out.
• Large items may block the tools or nozzle. If any part becomes blocked the
appliance may overheat and automatically cut-out.
• Leave to cool down for 1-2 hours before checking the filter or for blockages.
• Ensure the appliance is disconnected from the charger before looking for
blockages. Failure to do so could result in personal injury.
• Clear any blockage before restarting.
• Refit all parts of the appliance securely before using.
• Clearing blockages is not covered by your Dyson guarantee.
CHARGING AND STORING
• This appliance will switch ‘OFF’ if the battery temperature is below 3°C. This
is designed to protect the motor and battery. Do not charge the appliance and
then move it to an area with a temperature below 3°C for storage purposes.
• To help prolong battery life, avoid recharging immediately after a full discharge.
Allow to cool for a few minutes.
• Avoid using the appliance with the battery flush to a surface. This will help it run
cooler and prolong battery run time and life.
• If mounting the docking station on a wall, follow the instructions supplied with
this appliance. Ensure the docking station is fitted correctly and the right way
up, so the motor of the appliance is at the top when in place. Take all necessary
safety precautions. Use appropriate fixings, tools and safety equipment.
• When charging via the docking station the battery must be in the appliance.
• The battery can be charged on or off the appliance. Take care when removing
the battery.