Filter
Top Products
Preliminary
The KP-FD30 is equipped with the progressive full
frame RGB output of high frame rate( approx. 60
frame per second ). Optionally The KP-FD30CL
outputs Camera-Link. Both camera is equipped the
external synchronization(HD/VD), the external trigger
function, etc., it is suitable for the image-processing
equipment input.
Major feature
Suitable for the image-processing equipment input.
Small lightweight size, since adoption of multi-connector with one cable.
High resolution and high color delity
By adoption of the progressive scan CCD image sensor and RGB primary
color mosaic lters, the picture of high vertical resolution and high color
delity can be acquired.
A new digital signal processor (DSP)
The clear picture of a high signal to noise ratio (S/N) is obtained by the new
digital signal processor (DSP) adoption which has improved luminance signal
processing, such as 5H enhancer processing.
CCD drive functions
.Preset electronic shutter ( settable 11 steps from 1/60 second to 1/50,000
second and
27 steps from 1/30 second to 8 second. )
.Variable electric shutter ( 1H steps from 1/60 second to Approx. 1/10,000
second )
.Auto electronic shutter[AES] ( from 1/60 second to approx. 1/50,000 second )
.Frame/ eld on demand ( one trigger and xed shutter modes )
Output of NTSC system (2:1 interlace scan) (KP-FD30 only)
It can be set as the image output of NTSC system (2:1 interlace scan) by
switch change
VGA Progressive Scan CCD Color Camera
KP-FD30/KP-FD30CL
1 / 2-inch RGB primary color lter progressive scan CCD image sensor RGB color camera
High frame rate 60 frame per second
Standard Optionally For OEM
Model KP-FD30 KP-FD30CL KP-FD30F KP-FD30USB
Output format Analog RGB Camera Link IEEEE-1394 USB2.0
Frame rate 60 frame per sec. 60 frame per sec. 30 frame per sec. 30 frame per sec.
Imaging device 1/2-inch progressive scan interline CCD
No. of effective pixels 659(H) × 494(V)
Unit cell size 9.9(H) x 9.9(V) m ( Square pixel )
Scanning area 7.48(H) × 6.15(V) mm
Color lter R, G, B primary color mosaic lters on chip
Scanning system
(Selectable by switch)
Progressive scan ( VGA mode )
2:1 interlace scan ( NTSC mode )
Frequency Horizontal: 31.468 kHz Vertical: 59.94 Hz
Sync system Internal / external ( HD/VD auto selection )
Internal sync output :HD/VD/SYNC 2 Vp-p/75 , Negative polarity
WE: 5 Vp-p, Negative
External sync input HD/VD 2 to 5 Vp-p, Negative polarity
EXT. Trigger input: Low 0 VDC, High 2 to 5 VDC
Video signal output RGB output (G on SYNC)
Y/C output ( Only at the NTSC mode )
VBS output ( Only at the NTSC mode)
S/N ( Y signal ) More than 50dB ( AGC, enhancer and gamma off )
Resolution
( Y signal at center )
Horizontal: 440 TV lines
Vertical: 480 TV lines ( VGA mode ) 350 TV lines ( NTSC mode )
Standard sensitivity 2,000 lx ( F5.6, 100IRE )
Minimum illumination 10 lx ( F1.4, AGC ON, 50IRE )
Sensitivity selection Gain Adjustable at AGC OFF and AGC Limit Gain
Electric shutter speed
PRESET
AES
VARIABLE
Selectable in 11 steps high spped shutter
OFF(1/60), 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000
1/10000, 1/20000, 1/30000, 1/50000 second
: Approx. 1H steps from 1/60 second to 1/10,000 second
Selectable in 27 steps low speed shutter
OFF(1/60), 1/30, 1/15, 1/10, 1/7.5, 1/6, 1/5, 1/3.75, 1/3, 1/2.5, 1/2,
1/1.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8 second
From 1/60 second to approx. 1/50,000 second
( Response : SLOW, NORMAL, FAST )
Approx. 1H steps from 1/60 second to 1/10,000 second
Auto level ontrol [ALC]
( The auto level control system of AES, lens iris and AGC. )
AVERAGE / PEAK&AVERAGE / AREA
( Scanning area is selectable from 9 area. )
Auto-iris lens
outputs [DC/VIDEO*]
DC ( Iris control voltage input type lens, cable length over 150mm )
: Coupling coil impedance Damper : 1,150 ±10% , Drive : 190 ±10%
Power supply : 12 VDC, 60 mA
Note :. "VIDEO" is optionally.
White balance Selectable in 3 modes
Auto-tracking[ATW]:2,500K~6,000K
preset [AWC] : (2,500K~10,000K)
R/B gain manual control [MANUAL] (2,500K~10,000K)
Text display 24 alpha-numeric characters in one line (only KP-FD30)
Picture adjustment Modes and settings can be selected and adjusted from
on-screen menu (only KP-FD30)
Remote control Modes and settings can be selected and adjusted from PC
by RS-232C level,
Power supply 12 VDC ± 10 %
Approx.360 mA(KP-FD30) pprox.370mA(KP-FD30CL)
(Including 60mA for auto-iris lens )
Lens mount C/CS mount ( Frange-back adjustment )
Ambient temperature
Operating : -10 to +50 C, (+14 to +122 F) 30 to 80 %RH
Storage : -20 to +60
C
(-4 to +144 F), 20 to 90 %RH
Vibration endurance
68.6 m/s
2
( 10 to 200Hz, 30 minutes each on XYZ axes )
Shock endurance 490 m/s
2
( vertical, horizontal, once each face )
External dimensions
58(W) x 58(H) x 48(D) ( not including lens and protrusions )
Mass Approx.220g ( without lens )
Note : If operated continuously, be sure to use at less than +40 C(104 F) for long term stable performance.
Please inquire detailed speci cations of KP-FD30CL.
Main speci cations