Filter
Top Products
6
F
F
l
l
a
a
s
s
h
h
C
C
o
o
n
n
n
n
e
e
c
c
t
t
i
i
o
o
n
n
f
f
o
o
r
r
E
E
x
x
t
t
e
e
r
r
n
n
a
a
l
l
S
S
t
t
r
r
o
o
b
b
e
e
s
s
When using an external strobe, connect the housing hotshoe
connector. Slide the connector into the hotshoe mount on the
camera from the back of the camera as shown. Slide the
connector
forward until
i
t stops. This
can be done
before or after
the camera is
s
ecured with
the mounting
bolt.
O
'ring
Housing Back
C
amera
H
ot Shoe
Connector
E
xternal Strobe Connector
W
aterproof Cap
M
ounting
Tray
C
C
a
a
u
u
t
t
i
i
o
o
n
n
:
:
Do not remove the External Strobe Connector’s waterproof cap
unless an external sync cord is going to be plugged in. Do not
remove waterproof cap or sync cord underwater.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
i
i
n
n
g
g
C
C
a
a
m
m
e
e
r
r
a
a
i
i
n
n
H
H
o
o
u
u
s
s
i
i
n
n
g
g
Before installing the camera, pull out on the controls in the front
section of the housing. This will allow the camera to slide in more
easily. Once the camera is installed and the lid snaps have been
closed, return the controls to their operating position.
CClloossiinngg tthhee HHoouussiinngg
1. Place housing face down in your lap.
2. Check to see that there is an o’ring
on the housing back that is clean
and in its proper location.
3. Guide the back onto the housing.
The o’ring should touch the housing
all the way around. There should
be an even gap all the way around
between the housing and the
housing back.
4. Lift the lid snaps so they are
extended and place the lid snap into
the corresponding hook on the
housing back.
5. To close the housing, push
down on the lid snaps until
they snap into place . Lid
snaps on opposite sides of
the housing should be closed
at the same time. Be sure they
are down far enough to engage
the lid-snap lock.
DDoouubbllee cchheecckk
- Once the housing is closed, check the o’ring seal.
Check the gap between the housing back and the housing, it
should be even all the way around.
Look through the clear plastic back at the o’ring. You should see a
darkened area where the o’ring is compressed against the
housing back. If you do not see an even black compression seal
all the way around the back, open the lid snaps, reseat the
housing back, and then close the lid snaps. Visually check the seal
again.
o’ring
housing back
housing back
housing
housing
o’ring
even gap
all 4 sides
PPrreeppaarriinngg ttoo IInnssttaallll ZZoooomm CCllaammpp && GGeeaarr SSlleeeevvee
Determine the type
of lens being used
on the camera.
Type 1 Lenses have
a lens opening that
is NOT larger in
diameter than the
zoom ring.
((FFiigg.. 11))
.
Type 2 Lenses have a lens
opening that IS larger in diameter than the zoom ring.
((FFiigg.. 22))
.
ZZoooomm CCllaammppss && GGeeaarr SSlleeeevveess IInncclluuddeedd wwiitthh HHoouussiinngg
There are 2 different
Zoom Clamps and
Gear Sleeves
provided with the
housing. Start with
the suggested Zoom
Clamp and Gear
Sleeve depending
on the Type of
lens being used.
See
((FFiigg.. AA oorr BB))
Figure B-Type 2 Lens
Figure A-Type 1 Lens
lens
opening
zoom
ring
bayonet
mount
Type 1 lens Type 2 lens
(Figure 1) (Figure 2)
Figure G
Normally used with
Type 1 lens (Fig.1)
#9059.8 small diameter clamp:
For use with #0073 sleeve
+
#0073 sleeve: Use with
small diameter zoom clamp
#9059.8
Figure A
Normally used with
Type 2 lens (Fig.2)
#5509.28 Package
#9059.9 large diameter clamp:
For use with #0073.1 sleeve
+
#0073.1 sleeve: Use with
large diameter zoom clamp
#9059.9
Figure B
thick ribs
thin ribs
wide
grooved
extension
tabs
narrow
grooved
extension
tabs
Figure F
7
8
I
I
n
n
s
s
t
t
a
a
l
l
l
l
i
i
n
n
g
g
t
t
h
h
e
e
C
C
a
a
m
m
e
e
r
r
a
a
Remove the back from the housing. The mounting tray for the
c
amera is secured to the housing back. Position the camera and
lens on the tray, and
then secure it with the
mounting bolt which
t
hreads into the
camera’s tripod socket.
Use a flathead
screwdriver
(recommended) or coin
to tighten the mounting
bolt so the camera
bottom is flush against
the tray.
NNOOTTEE::
Conversion Circuitry Strobe ID Switch is located on bottom
of camera tray.
SSeettttiinngg tthhee CCoonnvveerrssiioonn CCiirrccuuiittrryy SSttrroobbee IIDD SSwwiittcchh..
On the bottom of the camera tray is a switch for setting the DS
Substrobe ID. Set the switch to the Model of DS Substrobe being
used.
• When using dual
strobes of different
models such as a
DS51 and a DS125,
set the ID switch to
DS51 or the smaller
strobe.
125
1
60
D
S
DS
Set
D
S Substrobes
to TTL Mode
50/51
2
00
8
0
O‘ring
Mounting Bolt
Camera Tray
C
ANON
5