Filter
Top Products
10
O
O
p
p
t
t
i
i
o
o
n
n
a
a
l
l
A
A
c
c
c
c
e
e
s
s
s
s
o
o
r
r
i
i
e
e
s
s
BBaacckk oo--rriinngg
##00110099
O-rings last for several years if properly maintained. (See
maintenance) Always carry a spare in case o-ring becomes
damaged or lost.
WWiiddee--AAnnggllee AAddaapptteerr
##99330066..8800
Required to mount Inon UWL-150AD Bayonet style wide-angle lens.
WWiiddee--AAnnggllee AAddaapptteerr
##99330066..8811
Required to mount Ikelite W-20 and other Screw Thread
(67mm) style wide-angle lenses.
UURR//PPrroo FFiilltteerr ((BBlluuee WWaatteerr))
##66444411..3322
The UR/Pro underwater color correcting filter is designed to
restore some of the warm colors filtered out by the water. For
available light use only, not recommended for use with flash.
GGrreeeenn WWaatteerr FFiilltteerr
##66444411..7722
Enhances contrast and alters the color of green water to
give our subject a rich, natural tone. For available light
only, not recommended for use with flash.
TTrraayy wwiitthh RReelleeaassee HHaannddllee
##99552233..3311
Tray and Release Handle is required
to mount external Substrobes.
IIkkeelliittee WW--2200 WWiiddee--AAnnggllee LLeennss
##66442200
Wide-Angle lenses allow you to capture more of the scene and
get closer to your subject which results in clearer images and
more vivid color. Can be installed or removed underwater for
maximum versatility. (Note: some housings may require an
adapter, see instructions.)
11
Substrobe
DS125
SSuubbssttrroobbee DDSS112255
The Substrobe DS125 covers
the equivalent of a 18mm
lens, 100 degrees. It is the
ideal choice when using
accessory wide angle lenses
greater than 28mm.
Substrobe
DS51
EV Controller
SA-100R
Arm
SA-100R
Arm
SSuubbssttrroobbee DDSS5511
The Substrobe DS51 covers
the equivalent of a 28mm lens.
It is the ideal choice when
using only the camera lens
or the camera lens with a
macro accessory lens.
OOppttiioonnaall AAcccceessssoorriieess CCoonnttiinnuueedd
EV Controller
9
D
D
i
i
f
f
f
f
u
u
s
s
e
e
r
r
a
a
n
n
d
d
D
D
e
e
f
f
l
l
e
e
c
c
t
t
o
o
r
r
c
c
o
o
n
n
t
t
.
.
A diffuser and deflector are
included with the housing. The
diffuser is white transparent
plastic. The deflector is also
white but is not transparent.
To install the diffuser or
deflector spread the port
clamp at the spring end and
slide over the lens port. The
white plastic should be placed
in front of the camera flash.
The port clamp should be
p
ushed back against the
front of the housing.
DDiiffffuusseerr
The diffuser should be installed when using the camera's built
in flash. When shooting with the camera's built-in flash at
approximately 2 feet (0.6 m) or less, the lens port on the
housing may block a portion of the light from the camera's
built-in flash, creating a shadow in the lower left of the photo.
If this occurs, zoom the lens slightly to eliminate the shadow.
(You can test this above water)
DDeefflleeccttoorr
The deflector should be installed when using an external strobe
such as the DS51 or DS125 Substrobe and EV Controller. The
deflector will redirect the camera's flash to the EV Controller
which controls the external strobes output.
Diffuser/
Deflector
material
Port Clamp
Spring
Spread to Install
This edge
against
housing
12
MMaaiinntteennaannccee
The Ikelite Digital Housing should be given the same care and
attention as your other photographic equipment. In addition to
normal maintenance we recommend that the housing be returned
to Ikelite periodically to be checked and pressure tested.
1.
DDoo NNoott
leave the camera and housing in direct sunlight for
prolonged periods. Heat may damage the camera.
2.
DDoo NNoott
ship the camera in the housing.
3. Before using the housing, always check the tightness of the
sseett ssccrreeww
in each control knob.
Check each
ccoonnttrrooll ggllaanndd
to make sure they are tight. There
is a slight chance that either could vibrate loose during travel.
4. Keep the back o-ring clean and lightly lubricated. To lubricate
remove the o-ring from the back. Put a small amount of lkelite
lubricant on your fingers. Draw the o-ring through your fingers
to apply a light coating of lubricant. Only apply enough
lubricant to make the o-ring feel slick.
DDoo NNoott ssttrreettcchh tthhee
oo--rriinngg
. This light coating of lubricant will help to keep the
o-ring from drying out and will help to show a dark sealing
line when the housing back is properly sealed.
5. Keep the area where the o-ring fits and the sealing surface
of the housing clean.
6. Rinse the housing exterior in fresh water after each salt water
use. Dry with a soft cloth. Dry lens port to eliminate spotting.
After several uses in salt water soak the housing in a mild soap
solution, rinse and dry before storage. When storing the
housing, remove the back o-ring, lightly lubricate and place
in a plastic bag. Place the plastic bag with o-ring inside the
housing for safe keeping.
CCAAUUTTIIOONN
N
N
e
e
v
v
e
e
r
r
u
u
s
s
e
e
s
s
p
p
r
r
a
a
y
y
l
l
u
u
b
b
r
r
i
i
c
c
a
a
n
n
t
t
s
s
a
a
s
s
t
t
h
h
e
e
p
p
r
r
o
o
p
p
e
e
l
l
l
l
a
a
n
n
t
t
i
i
n
n
g
g
r
r
e
e
d
d
i
i
e
e
n
n
t
t
c
c
a
a
n
n
c
c
a
a
u
u
s
s
e
e
t
t
h
h
e
e
p
p
l
l
a
a
s
s
t
t
i
i
c
c
h
h
o
o
u
u
s
s
i
i
n
n
g
g
t
t
o
o
c
c
r
r
a
a
c
c
k
k
.
.