Filter
Top Products
66
EN
Indications Function
Displays the battery remaining power.
Remaining power level: high
Remaining power level: exhausted
As the battery power comes close to nil, the battery indicator
blinks.
When the battery power is exhausted, power turns off automatically.
Appears when no tape is loaded. (੬ pg. 12)
Appears when the erase protection tab is set to “SAVE” while the Power Switch is set to
“
AUTO
” or “
M
A
NU
A
L
”.(
੬
pg. 12)
Appears if dirt is detected on the heads during recording or playback.
Use an optional cleaning cassette. (
੬ pg. 59)
Appears if condensation occurs. When this indication is displayed, wait more than
1 hour until condensation disappears.
Appears if a tape is not loaded when the Recording Start/Stop Button or SNAP-
SHOT Button is pressed while the Power Switch is set to “
AUTO
” or “
M
A
NU
AL
”.
Appears when the tape ends during recording or playback. (੬ pg. 52)
Appears if a tape in another format is loaded.
● Appears when the date/time is not set. (੬ pg. 11)
● Appears when the built-in clock battery runs out and the previously set
date/time is erased. Consult your nearest JVC dealer for replacement.
Appears for 5 seconds after power is turned on if the lens cap is attached.
Appears if Audio Dubbing is attempted on a blank portion of a tape.
(੬ pg. 48)
● Appears if Audio Dubbing is attempted on a tape recorded in the LP mode.
(
੬ pg. 48)
● Appears if Audio Dubbing is attempted on a tape recorded in 16-bit audio.
(੬ pg. 48)
● Appears if A. DUB (e) on the remote control is pressed when the erase protection
tab is set to “SAVE”.(
੬ pg. 48)
Appears if Insert Editing is attempted on a blank portion of a tape. (੬ pg. 49)
● Appears if Insert Editing is attempted on a tape recorded in the LP mode.
(
੬ pg. 49)
● Appears if INSERT (w) on the remote control is pressed when the erase
protection tab is set to “SAVE”.(੬ pg. 49)
The error indications (E01, E02 or E06) show what type of malfunction has occured.
When an error indication appears, the camcorder turns off automatically. Remove
the power supply (battery, etc.) and wait a few minutes for the indication to clear.
When it does, you can resume using the camcorder. If the indication remains,
consult your nearest JVC dealer.
The error indications (E03 or E04) show what type of malfunction has occured. When
an error indication appears, the camcorder turns off automatically. Eject the cassette
once and re-insert it, then check if the indication clears. When it does, you can resume
using the camcorder. If the indication remains, consult your nearest JVC dealer.
Warning Indications
TAPE!
TAPE END
SET DATE/TIME!
CHECK TAPE’S ERASE
PROTECTION TAB
HEAD CLEANING
REQUIRED USE
CLEANING CASSETTE
CONDENSATION
OPERATION PAUSED
PLEASE WAIT
DIFFERENT
FORMATTED TAPE
A. DUB ERROR!
<CANNOT DUB
ON A LP RECORDED TAPE>
<CANNOT DUB
ON A 16BIT
RECORDING>
<CHECK TAPE’S ERASE
PROTECTION TAB>
A. DUB ERROR!
LENS COVER
INDEX
Indications (cont.)
INSERT ERROR!
<CANNOT EDIT
ON A LP RECORDED TAPE>
<CHECK TAPE’S ERASE
PROTECTION TAB>
INSERT ERROR!
E01, E02 or E06
UNIT IN SAFEGUARD
MODE REMOVE AND
REATTACH BATTERY
E03 or E04
UNIT IN SAFEGUARD
MODE EJECT AND
REINSERT TAPE