Filter
Top Products
6 KODAK PROFESSIONAL PLUS-X 125 Film / 125PX • F-4018
FINAL STEPS
65 to 75°F (18 to 24°C).
MACHINE PROCESSING
Roller-Transport Processors
KODAK VERSAMAT Film Processors
You can process this film in roller-transport processors, such
as the KODAK VERSAMAT Film Processor, Model 5, 11,
or 411, with KODAK DURAFLO RT Developer Starter,
KODAK DURAFLO RT Developer Replenisher, and
KODAK Rapid Fixer.
Processing Steps and Conditions for KODAK
VERSAMAT Film Processors
The recommended machine speeds for processing
KODAK PROFESSIONAL PLUS-X 125 Film to a contrast
index of 0.56 is as follows:
Step/Solution Time (min:sec)
Rinse—with agitation:
KODAK Indicator Stop Bath 0:30
KODAK EKTAFLO Stop Bath 0:30
Fix—with frequent agitation:
KODAK Fixer 5:00 to 10:00
KODAK Rapid Fixer 2:00 to 4:00
KODAFIX Solution 2:00 to 4:00
KODAK POLYMAX T Fixer (1:3) 2:00 to 4:00
Wash:
Running Water
—OR—
Rinse with water
KODAK Hypo Clearing Agent
Running water
20:00 to 30:00
0:30
1:00 to 2:00
5:00
Final Rinse:
KODAK PHOTO-FLO Solution 0:30
Dry—in a dust-free place
KODAK PROFESSIONAL PLUS-X 125 Films
Step
No. of
Racks
Path Length
Temperature
Model 11
Models 5
and 411
Develop 2
8.5 ft
(2.6 m)
4 ft (1.2 m)
80 ± 0.5°F
(26.5 ± 0.3°C)
Fix 3 12 ft (3.8 m) 6 ft (1.9 m)
80°F (26.5)
nominal
Wash 2 8 ft (2.4 m) 4 ft (1.2 m)
70 to 75°F
(21 to 24°C)
Dry 8 ft (2.4 m) 4 ft (1.2 m)
105 to 140°F
(40.5 to 60°C)
Processor PLUS-X 125 Film
KODAK VERSAMAT Film Processor,
Models 5 and 411
4.0 ft (1.2 m) per
minute
KODAK VERSAMAT Film Processor,
Model 11
8.5 ft (2.6 m) per
minute
You may need to use higher dryer temperatures (135 to
140
°F[57 to 60°C]) to dry several sheet films processed in
succession. If you are processing only roll films, a lower
temperature will be adequate.
Processing Conditions for Other Roller-Transport
Processors
Adjust the machine speed so that the development time for
normally exposed film is approximately 60 seconds. The
development time is measured from the time the film enters
the developer to the time it enters the fixer. Differences in
machine design that affect agitation and crossover times
from one tank to the next may require development-time
adjustments.
Replenishment Rates
Developer—Because most film loads will consist of a
variety of film types, use an average replenishment rate of
0.20 mL per square inch of film processed.
Fixer—Use 0.55 mL per square inch.
Large Tank Rack-and-Tank Processors
The development times for large-tank rack-and-tank
processors are based on a machine speed that transfers the
film every 2 minutes. The times given below are
starting-point recommendations. Make tests to determine if
results are acceptable for your needs.
Replenishment Rates
Stir or recirculate the solution after each addition of
replenisher solution.
T-MAX RS Developer—Add 45 mL (1.5 ounces) of
replenisher solution for each 135-36 or 120 roll of film
processed.
Note: Do not use T-MAX RS Developer and Replenisher to
replenish T-MAX Developer. They are not designed to work
together.
D-76 and XTOL Developers—Add 70 mL (2.4 ounces)
of replenisher solution for each 135-36 or 120 roll of film
processed.
Note: Refer to KODAK Publication No. J-78,
KODAK PROFESSIONAL Developer D-76, for modified
replenisher mixing instructions.
Large-Tank Rack-and-Tank Processing
EI
KODAK Developer or
Developer and
Replenisher
Time (min) at
72°F (22°C)
125/22°
250/25°
T-MAX RS 3
1
⁄
2
to 6
125/22°
250/25°
D-76 4 to 6
125/22°
250/25°
XTOL 4 to 6