Filter
Top Products
—
www.metz.de
Manual flash mode
Flash mode with unregulated light output.
The flash unit delivers the full light output,
provided no partial light output is set.
Manual zoom
The zoom position of the main reflector and
thus the illumination of the flash unit can be
adjusted manually to the focal length of the
lens.
Metal stand
High-quality metal base for secure
attachment on camera shoe.
Modelling light
The modelling light is a stroboscope light
with a high flash frequency lasting a few
seconds. This “quasi permanent light”,
allows you to evaluate the light distribution
and shadow formation on the subject before
taking the photograph.
Motor zoom
The zoom position of the main reflector and
thus the illumination of the flash unit is
automatically adjusted to the focal length of
the lens.
Partial light mode
Manual flash mode with unregulated light
output. By setting partial light mode on the
flash unit, the light output or illumination
duration of the flash unit can be specically
adapted to the photographic situation.
P-TTL
Innovative advancement of the TTL flash
control with metering pre-flash technology
for Pentax cameras.
REAR
Synchronisation to the 2nd shutter curtain
for more natural blur eects for longer
exposure times.
Remote mode
A remote system consists of a master or
controller flash unit on the camera and one
or more slave flash units. The slave flash
unit is wirelessly remotely controlled by
the master or controller flash unit. Unlike a
controller flash unit, with a master flash unit,
the flash contributes to the exposure.
SCA-3002 adapter system
For system cameras with digital or analog
data transmission between the camera and
flash unit. By using an SCA adapter from
the SCA 3002 system, there are numerous
additional system flash functions available
with flash units from the SCA 3002 system,
depending on the type of camera. The
rmware of an SCA adapter from the SCA
3002 system can be updated via Metz
Service for future cameras.
Secondary reflector
To brighten shadows cast at close range
which appear when using an indirect flash.
Servo mode
The servo mode allows you to operate the
Metz flash unit of the corresponding camera
system wirelessly with the built-in flash unit
on the digital camera. It allows light output
to be manually calibrated as partial lighting.
Slave mode
An integrated sensor makes this wireless
slave flash mode possible in combination
with a master or controller flash unit. (>>>
Remote mode)
Sony / ADI
Innovative further development of the TTL
flash control for Sony Alpha cameras in
which, for example, information regarding
the distance to the subject is included in the
flash exposure.
Spot zoom mode
While zooming the reflector increases by one
illumination level on the object over the
selected position. This centrally highlights
the shot. Example: the zoom reflector
adjusts to 70mm for a set focal length of
50mm. The information in the display of the
flash unit remains however at 50mm, the
original focal length of the lens.
Strobe mode
Manual flash mode for flash sequences with
a selectable intensity, frequency, and flash
number, e.g. for special eect photos and
motion studies.
Swivel reflector
Can be tilted horizontally and vertically for
bouncing flash. Can be tilted vertically for a
bouncing flash.
Touch display
Illuminated graphic display that can be
operated by touching the display panel.
TTL ll-in flash control
Reduces too high subject contrast (e.g. to
brighten dark shadowy areas in bright
sunshine).
TTL mode
While taking the photograph, the flash is
measured through the lens (TTL = through
the lens) by a sensor in the camera. The light
output of the flash unit is terminated as soon
as the subject is correctly exposed.
USB
Interface for rmware updates via the
Internet.
Wake-up
The flash unit can be reactivated by lightly
depressing the shutter if it has been in
energysaving standby mode aer an
extended break from taking photographs. (>>>
Automatic unit switch-o)
Wide-angle adapter
Increases the light angle of the flash unit.
Depending on the type of flash unit, the
wide-angle attachment is available either
integrated or attachable as an accessory.