Filter
Top Products
Mid Level Spreader (Fig 5.)
The Mid Level Spreader allows the setting of the Tripods footprint and ne
height adjustment. The tripod height and overall footprint can be adjusted
by turning the Spreader Adjusting knob or by adjusting the length of the
telescopic spreader arms.
Spreader Set-up
1. Turn the Spreader Adjusting Knob counter-clock wise to the open
position.
2. Stand the Tripod upright with legs spread out equally.
3. Release the Telescopic Clamp on the spreader arm then latch the Quick
Release Latch on to the Self Aligning Swivel, repeat for the remaining
two arms.
4. Bring each Tripod leg in such that the corresponding Spreader arm is
fully retracted then lock the Telescopic Clamp, repeat for each Spreader
arm.
5. Bring the Tripod legs towards the centre position, if resistance is felt do
not force the Tripod legs, spread out the Tripod legs and make sure that
the Spreader arms are fully retracted.
Spreader Pull Down
1. Remove the Camera and the Fluid Head from the Tripod.
2. Stand the Tripod upright with legs spread out equally and the Mid Level
Spreader in the open position.
3. Pull back the Quick Release Latch knob and lift the Spreader arm from
the Self Aligning Swivel, repeat for the remaining two arms.
Ground Spreader (Fig 6.)
The Miller Ground Spreader provides adjustment of each spreader arm to
allow for lower height settings or uneven ground.
Spreader Set-up
1. Place the Ground Spreader on at ground.
2. Place the socket of the Tripod Foot on to the ball of the Rubber Foot then
pull the Rubber Stirrup up and over the Tripod Foot shoulder, repeat for
the remaining two Tripod Feet.
Spreader Pull Down
1. Remove the Camera and the Fluid Head from the Tripod.
2. Pull the Rubber Stirrup up and outwards over the Tripod Foot shoulder,
repeat for the remaining two Tripod Feet.
Lower Leg Lock: (Fig 8.)
For 2 stage Sprinter II Tripod only.
Adjust the Lower Leg Lock Assembly in locked position using a (supplied)
5mm Hex Key. - P6579
1. Extend the lower stage half way and lock the Lower Lever.
2. Tighten the lower leg lock adjuster screw gradually clockwise 1/8th of a
turn. Release Lower Lever and ensure leg slides freely.
3. When adjusted correctly Leg Lock Lever should only have a small
amount of “free play” before locking action commences. If this free
play is excessive repeat the steps above.
When nished, ensure that all Leg Lock Levers
lock ush with the tripod brackets.
Test each leg lock assembly by:
· Unlocking and locking lever several times.
· The lever should close with a denitive ‘click’.
· The end of the lever should close against the bracket.
· The tripod legs must slide freely when unlocked.
GROUND SPREADER
Adjustment Knob
TRIPOD SET-UP
SPREADERS
CARRY HANDLE
TRANSPORT CLIPS
SAFETY
MAINTENANCE
1. Before setting-up the tripod, the Mid Level Spreader or the Ground
Spreader must be attached.
2. Remove tripod from the Softcase and unclip the Transport Clips.
3. Place the Tripod Feet on level surface (if possible) and release the
Sprint Lok Upper Lever on each leg.
4. Lift the top of the tripod to a desired height and then apply the Sprint
Lok Upper Lever on each leg.
5. Release the Sprint Lok Lower Lever on each leg, then lift the tripod
to a desired height and then apply the Sprint Lok Lower Lever on
each leg.
6. Spread the Tripod Legs apart, check that the Tripod Bowl is approxi-
mately level to the ground.
7. Check that the tripod is secure.
The Sprinter II Inline patented Carry
handle (g 4.) is designed so the
Sprinter II tripod and uid head remain
balanced while being carried by hand.
The rubber handle offers secure grip,
while the exible nylon attachments let
it rest, between the tripod legs, during
shooting.
The 2 Transport Clips (Fig 3), are
designed to hold the Sprinter tripod’s
three legs together during transport.
Their spring-loaded design means they
are easily gripped and detached for
set up, and reattached. The Transport
Clips must be securely attached before
transporting the tripod.
Ensure that all equipment is operating correctly and free from defects and
damage, also please ensure that the tripod is steady, secure and that the
bowl is approximately horizontal when attaching the camera. The operator
is responsible for the safe operation of this equipment.
1. Do not exceed the maximum payload capacity of the Tripod.
2. Do not leave the camera unattended on the Fluid Head.
3. Do not adjust the tripod Leg locks whilst the camera is attached to the
Fluid Head.
4. Do not move the Tripod whilst the camera is attached to the Fluid
Head.
5. Do not remove the Mid Level Spreader or Ground Spreader whilst the
camera and uid head is attached.
Regularly inspect the tripod, paying particular attention to any tube
damage, leg lock adjustment, leg top adjustment, condition of the bowl rim,
spreader mounting points, carry handle and feet.
Keep grit and dirt out of Sprint Loks as much as possible, including behind
levers. Regularly clean the tripod with a clean damp rag or soft brush. Wipe
off all sand, dust and salt spray.
Do not clean with solvents, cleaning uids, lubricants, polishes, abrasives
or wire brushes.
Transport and store the tripod in Miller case wherever possible. Store the
tripod in a dry place, away from direct sunlight.
LEG LOCK ADJUSTMENT
Over time the leg locks may need adjusting to prevent leg slippage.
Upper Leg Lock: ( Fig 7.)
For 1 & 2 stage Sprinter II Tripod.
Adjust the Upper Leg Lock Assembly in a locked position using (supplied)
5mm Hex Key - P6579.
1. Extend the upper stage half way and lock the Upper Lever.
2. Turn the Upper Leg lock adjuster clockwise 1/8th of a turn. Release
Sprint Lok Upper Lever and ensure that stage slides freely.
3. When adjusted correctly Leg Lock Lever should only have a small
amount of “free play” before locking action commences. If this free
play is excessive repeat the steps above.
Transport Clip
Telescopic Clamp
Quick Release Latch
Spreader Adjusting Knob
MID LEVEL
SPREADER
LEG TO BOWL ADJUSTMENT
The leg to bowl pivot joint on the Sprinter tripod should have no lateral or
free play movement and should swing with a rm, smooth resistance.
Adjustment is usually not required; however, should it become necessary,
the following procedure must be observed. (Fig 9.)
1. Leg to Bowl Adjustment to eliminate lateral or free play movement:
Using a cross head screwdriver, ensure Bracket Mounting Screws
on both sides of the Leg Top Bracket are tight. Retighten if necessary.
Check all legs.
2. Leg pivot or ‘swing’ adjustment to ensure rm, smooth resistance.
Tighten the Leg Pivot Screws on each side of the Leg Top Bracket
using a 4mm Hex key until a smooth resistance is maintained. Check
all legs.
Leg Top Bracket
4mm Hex Key
Leg Pivot Screw
#2 Pozi Head
Screw Driver
Bracket Mounting
Screws
Fig 5.
Fig 6.
Fig 4.
Fig 3.
Fig 7.
Fig 9.
5mm Hex key
5mm Hex key
Fig 8.
TRIPOD PULL DOWN
1. Remove the camera from the Fluid Head.
2. Retract the spreader arms fully.
3. Hold and lift off the ground by two legs, then bring the legs inwards.
4. While holding the top of the tripod, release the Sprint Lok Upper Lever
and Sprint Lok Lower Lever on each leg then lower completely.
5. Apply the Sprint Lok Upper Lever and Sprint Lok Lower Lever on
each leg.
6. Attach both Transport Clips and return the tripod to the Softcase.