Filter
Top Products
4
5. Feed camera leads through hole in mounting surface. Connect wires (see WIRING.)
6. Place assembled camera housing into main bracket.
7. Place dome over camera housing and attach to main bracket with 3 large screws.
Do not tighten completely.
8. Make provisions to view the camera image and point the camera at the desired location.
Note: Make sure image is level!
9. With camera properly aimed, tighten screws.
WIRING
NOTE: THE CAM-PB REQUIRES RG6 OR RG59 COAXIAL CABLE FOR VIDEO, AND TWO-CONDUCTOR,
18 AWG WIRE FOR POWER. USE THE CAMERA’S INCLUDED POWER SUPPLY FOR PROPER
OPERATION. NO CABLES OR WIRES ARE SHIPPED WITH THE CAMERA KIT.
Main
bracket
Camera
housing base
Camera
housing top
Dome
Use 1/2" Screws
Use 1/4" Screws
Use 1/2" Screws
1. Adjust view
2.Tighten screws
Remove
Red
Black
+
–
Stripe = +
12VDC
RG6 or
RG59
Coax
Male RCA to
female F
connector
To video display,
Z880, MOD3000 etc.
Supplied with CAM-PB
Main
bracket
Camera
housing base
Camera
housing top
Dome
Use 1/2" Screws
Use 1/4" Screws
Use 1/2" Screws
1. Adjust view
2.Tighten screws
Remove
Red
Black
+
–
Stripe = +
12VDC
RG6 or
RG59
Coax
Male RCA to
female F
connector
To video display,
Z880, MOD3000 etc.
Supplied with CAM-PB
Main
bracket
Camera
housing base
Camera
housing top
Dome
Use 1/2" Screws
Use 1/4" Screws
Use 1/2" Screws
1. Adjust view
2.Tighten screws
Remove
Red
Black
+
–
Stripe = +
12VDC
RG6 or
RG59
Coax
Male RCA to
female F
connector
To video display,
Z880, MOD3000 etc.
Supplied with CAM-PB
Figure 4
Figure 5
Figure
6
Main
bracket
Camera
housing base
Camera
housing top
Dome
Use 1/2" Screws
Use 1/4" Screws
Use 1/2" Screws
1. Adjust view
2.Tighten screws
Remove
Red
Black
+
–
Stripe = +
12VDC
RG6 or
RG59
Coax
Male RCA to
female F
connector
To video display,
Z880, MOD3000 etc.
Supplied with CAM-PB
Main
bracket
Camera
housing base
Camera
housing top
Dome
Use 1/2" Screws
Use 1/4" Screws
Use 1/2" Screws
1. Adjust view
2.Tighten screws
Remove
Red
Black
+
–
Stripe = +
12VDC
RG6 or
RG59
Coax
Male RCA to
female F
connector
To video display,
Z880, MOD3000 etc.
Supplied with CAM-PB
Main
bracket
Camera
housing base
Camera
housing top
Dome
Use 1/2" Screws
Use 1/4" Screws
Use 1/2" Screws
1. Adjust view
2.Tighten screws
Remove
Red
Black
+
–
Stripe = +
12VDC
RG6 or
RG59
Coax
Male RCA to
female F
connector
To video display,
Z880, MOD3000 etc.
Supplied with CAM-PB
Main
bracket
Camera
housing base
Camera
housing top
Dome
Use 1/2" Screws
Use 1/4" Screws
Use 1/2" Screws
1. Adjust view
2.Tighten screws
Remove
Red
Black
+
–
Stripe = +
12VDC
RG6 or
RG59
Coax
Male RCA to
female F
connector
To video display,
Z880, MOD3000 etc.
Supplied with CAM-PB
Main
bracket
Camera
housing base
Camera
housing top
Dome
Use 1/2" Screws
Use 1/4" Screws
Use 1/2" Screws
1. Adjust view
2.Tighten screws
Remove
Red
Black
+
–
Stripe = +
12VDC
RG6 or
RG59
Coax
Male RCA to
female F
connector
To video display,
Z880, MOD3000 etc.
Supplied with CAM-PB
DS00470ACN-0 CAM-DFMK small.indd 6 1/11/06 11:19:42 AM