Filter
Top Products
S-1
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Block Diagram .......................................................................... S-2
S2.1. Overall Block Diagram ..........................................................S-2
S3. Schematic Diagram .................................................................. S-3
S3.1. Interconnection Diagram ....................................................... S-3
S3.2. Flash Schematic Diagram ..................................................... S-4
S3.3. Top Operation Schematic Diagram ....................................... S-5
S3.4. AF Assist Schematic Diagram ............................................... S-5
S3.5. CCD Flex Schematic Diagram (DMC-TZ2) ........................... S-6
S3.6. CCD Flex Schematic Diagram (DMC-TZ3) ........................... S-7
S3.7. Lens Flex Schematic Diagram .............................................. S-8
S4. Print Circuit Board .................................................................... S-9
S4.1. Flash P.C.B. ..........................................................................S-9
S4.2. Top Operation P.C.B. ........................................................... S-10
S4.3. AF Assist P.C.B. .................................................................. S-10
S4.4. CCD Flex P.C.B. (DMC-TZ2) .............................................. S-11
S4.5. CCD Flex P.C.B. (DMC-TZ3) ..............................................S-12
S4.6. Lens Flex P.C.B. .................................................................. S-13
S5. Replacement Parts List .......................................................... S-15
S6. Exploded View .......................................................................S-20
S6.1. Frame and Casing Section.................................................. S-20
S6.2. Packing Parts and Accessories Section (1) ........................ S-21
S6.3. Packing Parts and Accessories Section (2) ........................ S-22
Table of contents
Service Manual
DSC0703017CE/DSC0703019CE
Diagrams and Replacement
Parts List
Vol. 1
(S)...........Silver Type
Colour
(K)...........Black Type (except DMC-TZ2PL/GD/GT)
(A)...........Blue Type (only DMC-TZ3P/PC/EB/EE/EF/EG/EGM/GC/SG)
Model No.
DMC-TZ2P
DMC-TZ2PC
DMC-TZ2PL
DMC-TZ2EB
DMC-TZ2EE
DMC-TZ2EF
DMC-TZ2EG
DMC-TZ2EGM
DMC-TZ2GC
DMC-TZ2GD
DMC-TZ2GK
DMC-TZ2GN
DMC-TZ2GT
DMC-TZ3P
DMC-TZ3PC
DMC-TZ3PL
DMC-TZ3EB
DMC-TZ3EE
DMC-TZ3EF
DMC-TZ3EG
DMC-TZ3EGM
DMC-TZ3GC
DMC-TZ3GD
DMC-TZ3GK
DMC-TZ3GN
DMC-TZ3GT
DMC-TZ3SG
Digital Camera
Name of Signal
OFTR
FEP
This signal is connected
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice