Filter
Top Products
5. Supply the video output signal of the
camera to be adjusted and the refer-
ence gen-lock input signal to a dual-
trace oscilloscope.
6. Set the oscilloscope to the horizontal
rate and expand the horizontal sync
portion on the oscilloscope.
7. Move the cursor to H PHASE.
8. Adjust the horizontal phase by press-
ing L or M. The adjustable range is
0-2.0 µs.
6-3. Line-lock Sync Mode (LL)
Note: The line-lock (LL) sync mode is not available when the camera operates on DC
power.
1. Move the cursor to SYNC and select LL.
Note: The settings in this menu can be made only when the multiplexed vertical drive
signal (VD2) is not supplied to the
camera.
2. After confirming that the cursor is on
LL, press I. The vertical phase
adjustment menu appears on the moni-
tor screen.
3. Supply the video output signal of the
camera to be adjusted and the refer-
ence camera video output signal to a
dual-trace oscilloscope.
4. Set the oscilloscope to the vertical rate and expand the vertical sync portion on the
oscilloscope.
5. Move the cursor to COARSE. The cursor is highlighted.
6. Press L or M to match the vertical phase for both video output signals as closely as
possible. (COARSE adjustment can be incremented in 16 steps by 22.5 degrees by
pressing L or M.)
Note: After the sixteenth step, the adjustment returns to the first step.
7. Move the cursor to FINE.
8. Press L or M to match the vertical
phase for both video output signals as
closely as possible.
(FINE adjustment can be made by up
to 22.5 degrees by pressing L or
M.)
Notes:
• When the “I” cursor reaches the “+” end, it jumps back to “–”. At the same time,
COARSE is incremented by one step to enable a continuous adjustment. The
reverse takes place when the “I” cursor reaches the “–” end.
• When L or M is kept pressed for a second or more, the “I” cursor moves faster.
• To reset COARSE and FINE to the values preset at the factory, press L and M
simultaneously. COARSE and FINE adjustments are preset at the factory to zero-
crossing of the AC line phase.
• If the AC line contains noise (spike noise, etc.), the stability of the vertical phase of
the camera video output signal may be disturbed.
7. White Balance Setting (WHITE BAL)
7-1. Auto-Tracing White Balance Mode (ATW)
You can select one of three modes for white balance adjustment as follows:
The factory default setting is ATW1.
• ATW1 (Auto-Tracing White Balance 1)
Move the cursor to WHITE BAL and
select ATW1.
In this mode, the color temperature is
monitored continuously and thereby
white balance is automatically set. The
color temperature range for the proper
white balance is approximately 2 600 -
6 000K. Proper white balance may not
be obtained under the following condi-
tions:
1. The color temperature is out of the 2 600 - 6 000K range.
2. When the scene contains mostly high color temperature objects, such as a blue
sky or sunset.
3. When the scene is dim.
In these cases, select the AWC mode.
• ATW2 (Auto-Tracing White Balance 2)
Auto-tracing white balance in sodium lamp mode (ATW2)
When you select ATW2 for sodium lamp, white balance is automatically set (no opera-
tion needed).
Note: ATW1 and ATW2 do not appear for WHITE BAL on the system controller setup
menu.
• Automatic White Balance Control
Mode (AWC)
In this mode, accurate white balance is
obtained within a color temperature
range of approximately 2 300-10 000K.
1. Move the cursor to WHITE BAL and
select AWC → PUSH SW.
2. Press I to start the white balance
setup. The PUSH SW is highlighted to indicate that the white balance is being set.
3. When the white balance setting is completed, the PUSH SW returns to normal display.
Note: If white balance is not set, the PUSH SW is being highlighted.
4. When you want to adjust the white bal-
ance manually, press M to select
AWC and press I. The AWC menu
appears on the monitor screen. (When
ATW is selected, pressing I dis-
plays the ATW menu.)
1 (1 - - 16): 0 degrees
2 (1 - - 16): 22.5 degrees
16 (1 - - 16): 337.5 degrees
** SYNC **
V PHASE
COARSE 1(1--16)
FINE I........
- +
RET END
** SYNC **
H PHASE ........I
- +
RET END
** AWC **
R ....I....
- +
B ....I....
- +
MASK SET
RET END
↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER ---
AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF
LENS DRIVE DC
END SET UP ENABLE
↵↵↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER ---
AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL AWC
→
PUSH SW
MOTION DET OFF
LENS DRIVE DC
END SET UP ENABLE
↵↵
Highlighted