Filter
Top Products
Installation
1. Re-attach the vehicle’s negative battery cable.
2. Turn the ignition key to the accessory position, do not start the vehicle.
3. Engage the parking brake, then put the shifter in the reverse position.
4. Turn the monitor ON by pressing the ON/OFF button on the monitor.
5. Look at the monitor, if the image does not match your rear view mirror press the
Image Orientation button on the monitor to correct the image.
There are four different views for the monitor, each time the button is pressed the im-
age will change.
These different views allow you to mount the camera and/or monitor either right side
up or upside down and still display the image correctly on the monitor. The image
displayed should match your rear view mirror.
After testing the unit and you are satisfi ed with the route you have chosen for the
cabling, you must permanently install it.
Fully tighten the license plate bolts.
Route all wires behind interior panels or under carpeting so they are hidden.
Use supplied cable ties to neatly gather any excess wire.
©2007 Intellectual Solutions Inc. This product is covered by one or more of the following patents: U.S. Pat. No. 7,245,207, U.S. Des. Pat. No.
535,676, U.S. Des. Pat. No. 536,011, U.S. Des. Pat. No. 536,012, U.S. Des. Pat. No. 536,016,U.S. Des. Pat. No. 536,360, U.S. Des. Pat. No. 545,784
Other Patents Pending. All designs, logos and images are the exclusive property of Intellectual Solutions Inc. and/or its affi liates. All rights reserved.
100207 Printed in China 00000
SCOTCH-LOK
®
INSTRUCTIONS
CAMERA WIRING DIAGRAM
TESTING THE SYSTEM
+A
Mirror
Image
A+
Forward
Upside Down
A+
Normal
Image
A+
Mirror
Upside Down
Limited Warranty
WARNING: Changes or modifi cations to this equipment not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules, and applicable Industry Canada regulations. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation of device.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifi ctions to this equipment.
Such modifi cations could void the user’s authority to operate this equipment.
(For Canada)
This Class A/B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
FCC & Industry Canada Information
Insert the existing wire
to be tapped.
Insert the wire to be
attached.
Crimp tap with pliers,
then close lock
You do not need to use the Scotch-Lok
TM
connectors. The camera can be wired directly
to the reverse light circuit by stripping the reverse light wires then twisting the camera
wires to the exposed reverse light wires. Once connected, wrap with electrical tape. Do
not attempt this if you are not knowledgeable with electrical installation practices.
7. If you are going to drill a hole, choose a loca-
tion as close to the camera where the power
cable comes out of it. Before you drill a hole
you MUST CHECK and see WHAT IS BE-
HIND WHERE YOU ARE DRILLING. If there
are any vehicle components, such as electri-
cal parts or fuel system components behind
where you are drilling, you must take what-
ever precaution is necessary not to damage
them. Remove the license plate and camera
before drilling.
8. After you have drilled a hole, insert the sup-
plied grommet (Fig.4), then pass the power
cable through the grommet into the vehicle
(Fig.5). You must use the grommet to prevent
the metal edge of the hole from cutting the
power cable.
11. The reverse light sockets on most vehicles have two wires connected to them.
Usually the negative wire is black and the positive wire is a colored wire. If you are
uncertain about the wiring, you can use a 12 Volt test light available at most auto
parts stores to determine which is the positive wire.
a. Remove the reverse light socket from its housing, then remove the bulb from the
socket.
b. Engage the parking brake, turn the ignition key to the ON position, but do not start
the vehicle. Put the gear shift in the reverse position.
c. Attach the ground wire of the test light to the vehicle ground, then touch one of the
socket’s contacts with the positive lead.
e. If the test light lights up, then the wire corresponding to that contact is the positive
wire. If it doesn’t light up the opposite wire is the positive wire.
Follow the manufacturer’s instructions for the safe use of the test light.
Installation
6.
Some vehicles may have a hole available to pass
the wire through, (Fig.2) such as where the li-
cense plate light is mounted, or you can drill a
hole close to where the power cable is attached
to the camera. (Fig.3) Once you have chosen
where the cable will enter the vehicle’s body,
remove the camera. If you are able to use an
existing opening, skip the next two steps. If you
would like to use the “Wired” option instead of
Wireless go to www.vr-3.com
9. Next you’ll need to fi nd the vehicle’s reverse
lights. Turn the vehicle’s ignition key to the
accessory position, engage the parking
brake and put the car in reverse. Look at the
vehicle’s tail lights to see where the reverse
lights are located, they are the white lights.
To locate the reverse light’s 12V+ wire it will
be necessary to gain access to the rear of
the vehicle’s tail light.
For help locating the vehicle’s reverse light
circuit contact your vehicle’s manufacturer
for vehicle specifi c wiring diagrams.
Using an Existing Opening for Access
Fig.2
Drilling an Access Hole
Fig.3
Fig.4
Fig.5
10. Once you have located the reverse light cir-
cuit you will have to route the camera’s pow-
er cable to that location. You must securely
fasten the power cable to prevent it from be-
ing caught on any vehicle component such
as the trunk hinge (Fig.6). Never route the
cable on the outside of the vehicle.
Fig.6
12. After determining which wire is the positive and which is the negative, turn off the
ignition key, then remove the battery’s negative cable.
13.
Following the Scotch-Lok
TM
instructions section, splice the Red wire using the sup-
plied in-line Scotch-Lok
TM
wire connectors to the reverse light’s positive (+) wire.
Use a set of slip joint pliers to squeeze the TAP and insure good connection.
14. Next splice the black wire of the camera’s power cable to the reverse light’s nega-
tive (-) wire or ground.
15.
Replace the reverse light bulb, then re-install the light socket. Secure all the wires with
cable ties or electrical tape. Re-attach the negative battery cable to the battery.
Virtual Reality Video Labs
®
warrants, to the original purchaser, that its products are free from defects in material and
workmanship for 30 days from the date of original purchase, as part of our commitment to product excellence.
Virtual
Reality Video Labs
®
and/or it’s affi liates routinely improve the designs, materials or production methods of its exist-
ing products. Because it is impractical to publicize all changes in every product, we reserve the right to make such
changes without notice.
Disclaimer:
Virtual Reality Video Labs
®
and/or its affi liates, including without limitation
Virtual Reality Video Labs
®
, does
not guarantee or promise that the user of our Back-Up Cameras will not be in an accident or otherwise not collide with
an object and/or person. Our Back-Up Cameras are not intended in any way to be a substitute for careful and cautious
driving or for the consistent adherence to all applicable traffi c laws and motor safety regulations. These products are
not intended to be a substitute for rearview mirrors or for any other motor vehicle or boat equipment mandated by law.
Even when properly installed, our Back-Up Cameras have a limited fi eld of vision and do not provide a comprehensive
view of the rear area of the vehicle. You should always look around outside your vehicle and use your mirrors to confi rm
rearward clearance.
Virtual Reality Video Labs
®
and/or its affi liates, including without limitation
Virtual Reality Video Labs
®
, shall have no
responsibility, liability or the like for damage and/or injury resulting from accidents occurring with vehicles having the
Back-Up Camera installed. Except as specifi cally set forth herein, no warranty or representation, express or implied,
is made as to the Back-Up Cameras. Except as expressly modifi ed herein,
Virtual Reality Video Labs
®
and/or its af-
fi liates, including without limitation
Virtual Reality Video Labs
®
, specifi cally disclaims, without limitation, any statutory
warranties, implied warranty of merchantability or fi tness for a particular purpose.
Virtual Reality Video Labs
®
and/or its
affi liates, including without limitation
Virtual Reality Video Labs
®
, is not responsible for a user’s intended or actual use
of the Back-Up Cameras or results deriving therefrom. In no event, shall
Virtual Reality Video Labs
®
and/or its affi liates,
including without limitation
Virtual Reality Video Labs
®
, have any liability for any losses (whether direct or indirect, in
contract, tort or otherwise) incurred in connection with the Back-Up Camera, including but not limited to damaged
property, injury and/or loss of life. Neither shall
Virtual Reality Video Labs
®
and/or its affi liates, including without limita-
tion
Virtual Reality Video Labs
®
, have any liability for any decision, action or inaction taken by any person in reliance
on the Back-Up Camera, or for any delays, inaccuracies and/or errors in connection with the Back-Up Camera and
its functioning.
CONDITIONS OF WARRANTY:
If during the 30 day warranty period your new product is found to be defective,
Virtual Reality Video Labs
®
will repair
such defect, or replace the product, without charge for parts or labor subject to the following conditions:
1. All repairs must be performed by
Virtual Reality Video Labs
®
and/or it’s affi liates in Eatontown, New Jersey.
2. The equipment must not have been altered or been damaged through negligence, accident, or improper operation.
3.
The replacement of parts are exempted from this warranty when replacement is necessary due to normal wear and tear.
4. All warranty claims must be accompanied by a copy of the sales receipt or bill of sale.
5. Repair or replacement parts supplied by
Virtual Reality Video Labs
®
under this warranty are protected only for the
unexpired portion of the original warranty.
6. In the case of car stereos, this warranty does not extend to the elimination of car static or motor noise; correction
of antenna problems; costs incurred for the removal or reinstallation of the product; damage to tapes, speakers, ac-
cessories or car electrical systems.
7.
Virtual Reality Video Labs
®
will not be responsible for any charge incurred for installation.
OWNER’S RESPONSIBILITIES:
Virtual Reality Video Labs
®
will make every effort to provide warranty service within a reasonable period of time.
SHOULD YOU HAVE ANY QUESTIONS ABOUT SERVICE RECEIVED, OR IF YOU WOULD LIKE ASSISTANCE IN
OBTAINING SERVICE, PLEASE CALL TOLL FREE 1-800-445-1797, 8:30am - 4:30pm EST.
In order to provide you with the proper warranty service, we request that you adhere to the following procedure:
1. Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service.
2. If it is necessary to return your product for service, please return it securely packed, preferably in the original ship-
ping carton, and freight and insurance prepaid to the following address:
Virtual Reality Video Labs
, Service Department,
41 James Way, Eatontown, New Jersey 07724.
3. Please include a detailed explanation of the problem you are having.
4. If your product is found by
Virtual Reality Video Labs
®
to have a defect in material or workmanship, within the war-
ranty period, it will be repaired or replaced at no charge and returned to you prepaid. Where permitted by Iaw
Virtual
Reality Video Labs
®
liability shall be limited to that set forth in this warranty. This warranty shall be the exclusive remedy
of the purchaser.
Virtual Reality Video Labs
®
makes no other warranty of any kind, expressed or implied; and all implied warranties, are
hereby disclaimed by
Virtual Reality Video Labs
®
and excluded from this warranty,
Virtual Reality Video Labs
®
and/or
it’s affi liates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or
consequential, arising out of the use or intended use of the product.
USB CHARGING PORT
1. Insert one end of the USB charging cable into the device you want to charge.
2. Insert the other end of the USB charging cable into the port on the side of the
monitor.
3. Follow manufacturer’s instructions for safely charging the device you have con-
nected to the monitor.
If you would like to use the “Wired” option instead of Wireless go to www.vr-3.com