Sanyo Camera Lens Camera Lens User Manual


 
6
Model Description Camera Lens Housing Mount
VSE-P2351HBSA
330TVL Color Camera (VCC-3954), 2.8-12mm AI Vari-focal Lens,
3 1/2" x 16" Cylindrical Housing, Feed-thru Wall Mount, Heater,
Blower, Sunshield, Pre-cabled, 24VAC, outdoor
VCC-3954
SVCL-
CS2812VA
VSE-
2300
HBS
MTS-2000
VSE-P2352HBSA
330TVL Color Camera (VCC-3954), 5.0-50mm AI Vari-focal Lens,
3 1/2" x 16" Cylindrical Housing, Feed-thru Wall Mount, Heater,
Blower, Sunshield, Pre-cabled, 24VAC, outdoor
VCC-3954
SVCL-
CS550VA
VSE-
2300HBS
MTS-2000
VSE-P2361HBSA
520TVL Color Camera (VCC-6584), 2.8-12mm AI Vari-focal Lens,
3 1/2" x 16" Cylindrical Housing, Feed-thru Wall Mount, Heater,
Blower, Sunshield, Pre-cabled, 24VAC, outdoor
VCC-6584
SVCL-
CS2812VA
VSE-
2300HBS
MTS-2000
VSE-P2362HBSA
520TVL Color Camera (VCC-6584), 5.0-50mm AI Vari-focal Lens,
3 1/2" x 16" Cylindrical Housing, Feed-thru Wall Mount, Heater,
Blower, Sunshield, Pre-cabled, 24VAC, outdoor
VCC-6584
SVCL-
CS550VA
VSE-
2300HBS
MTS-2000
OUTDOOR COLOR MODELS
Model Description Camera Lens Housing Mount
VSE-P2461HBSA
520TVL Day/Night Camera (VCC-4594), 2.8-12mm AI Vari-focal Lens,
4 1/2" x 16" Cylindrical Housing, Feed-thru Wall Mount, Heater,
Blower, Sunshield, Pre-cabled, 24VAC, outdoor
VCC-4594
SVCL-
CS2812VA
VSE-
2400HBS
MTS-2000
VSE-P2462HBSA
520TVL Day/Night Camera (VCC-4594), 5.0-50mm AI Vari-focal Lens,
4 1/2" x 16" Cylindrical Housing, Feed-thru Wall Mount, Heater,
Blower, Sunshield, Pre-cabled, 24VAC, outdoor
VCC-4594
SVCL-
CS550VA
VSE-
2400HBS
MTS-2000
OUTDOOR DAY/NIGHT MODELS
5 INSTALLATION
Attention: This installation should be made by qualified service
personnel and conform to the National Electrical Code and
applicable local codes.
5.1 Operating Voltage
Recommended operating voltage is 24 V AC, 60 Hz.
5.2 Preparing the Unit
Remove the mount and housing assembly from the carton.
5.3 Mount
Prepare and secure the mount to the wall or mounting
surface as described in the Mounts Instruction Manual
included in the installation document packet.
5.4 Housing
Feed the cabling from the housing foot through the mount.
Additional cables such as those used for RS-232 connections
can be fed through the back fittings. Attach the housing to
the mount using the screws and washers provided in the
hardware kit. For additional information, refer to the
Wall Mount Instruction Manual and
Housing Instruction Manual.
5.5 Line Power and Video Signal Connection
The external video coax cable is equipped with a BNC
connector to accept video signal. Route and connect video
cable to the BNC connector. The external power cable will
be provided to allow for necessary stripping/preparation by
the installer. For additional information, refer to the
Installation manuals included in the Installation document
packet.
5.6 Camera/Lens Adjustment
The camera and lens come factory configured and ready for
operation. If custom setup is required, refer to the camera
Installation Instructions included in the Instruction Booklet
Packet.
5.7 Sunshield
Sunshields are provided with the outdoor packages. Refer to
the Sunshield Installation Manual for information.
CALL FACTORY FOR OTHER CONFIGURATIONS.