Filter
Top Products
CONNECTIONS, SETTINGS
●
●●
●
What you will need
• Peripheral equipment (such as monitor, digital video recorder or
time-lapse VCR)
• Cables for connecting peripheral equipment and camera
(coaxial cables, connecting plugs)
• Power adapter (24 V AC or 12 V DC)
• Attachable lens (Auto-iris lens recommended.)
●
●●
●
Coaxial cables supported
You can use any of the following coaxial cables:
• RG-59U (3C-2V) Length: About 250 m max.
• RG-6U (5C-2V) Length: About 500 m max.
• RG-11U (7C-2V) Length: About 600 m max.
CAUTION
• When using an RG-59U (3C-2V) cable, do not use it on piping or air
wiring.
• Select the cable to use according to the distance between the devices to
connect.
• If you use a cable other than the types above, the image or sync signal
will be attenuated and will not be transmitted correctly.
●
●●
● Attaching a lens
The 1/3-inch DC-type, CS mount auto-iris lens (sold separately) is
recommended.
1
Remove the lens cap.
2
Attach the lens.
Turn the lens slowly to attach it to
the camera.
3
Connect the lens plug to the
LENS terminal.
CAUTION
• Depending on the type of lens, the shape of the lens plug may differ. In
this case, contact the place of purchase or a Sanyo Authorized Service
Center.
• When attaching the lens, use a lens with a mount screw
(L) that is less than 7 mm in length. If a lens that exceeds
this size is used, the camera may be damaged and you
may not be able to attach it correctly.
• When attaching a C mount lens, attach the lens to the
camera after inserting the C mount ring (sold separately).
●
●●
●
Making connections
1
Connect the camera and peripheral equipment with cables.
2
Connect the power cable.
Secure the supplied clamping core to the power cable as
shown in Figure A.
<When using a 24 V AC adapter>
Connect 3 wire grounded cable# (use 18AWG+) to the ground
(GND) terminal as shown in Figure 1.
<When using a 12 V DC adapter>
Connect the cable as shown in Figure 2.
CAUTION
• When connecting the power cable to the camera, check that the
polarity is correct.
• To prevent fire hazard any UL listed wire rated VW-1, should be used
for the 24 V AC cable input terminal.
3
Insert the power adapter plug into the wall outlet.
The “POWER” indicator (red) lights.
●
●●
●
Camera attachment bracket
As shown in Figure B above, you can remove the camera
attachment bracket and reattach it to the camera bottom if you
want to attach the camera to the top of an object. If you remove
the camera attachment bracket, be sure to use the removed
screws when reattaching it (other screws may not fit).
CAUTION
When using the camera attachment stand (sold separately), select a
location that will be able to withstand the weight of the camera and stand
for many years, and fix them securely in place.
: VIDEO IN
: VIDEO OUT
Connections
Camera installation Camera adjustment/Settings
Camera screws (Shorter)
Bracket screws (Longer)
Monitor
Digital video recorder
or time-lapse VCR
1
VIDEO OUT VS IN
POWER
Figure 1 Figure 2
GND
AC24V
DC12V
24 V AC connection
GND
AC24V
DC12V
12 V DC connection
33
22
ON
BLC LL
PHASE LEVEL
LH
VIDEO
EI DC
OFF
1 2 3 4 5
Figure A
A
AA
A
Connections
1
2
3
L
B
BB
B
Camera installation
The camera comes pre-adjusted and ready to install at time of
factory shipment, but you may want to make adjustments or
settings to adapt to the operating conditions or installation
environment, if necessary.
If you have trouble adjusting the camera, contact your place of
purchase or a Sanyo Authorized Service Center.
• The settings shown for switches Ẅ ẅ and Ẉ are the settings at
time of factory shipment.
• Use a Phillips-head screwdriver to adjust dials Ẇ and ẇ .
(
★
★★
★
= Factory default setting)
Ẅ
Backlight compensation (BLC)
For adjusting backlight compensation. Use this setting to adjust
the backlight compensation when an image is backlit.
ẅ
Sync setting (LL)
Vertical sync disturbance may occur when a selector is used to
switch between multiple cameras connected to one monitor. To
prevent vertical sync disturbance, set to “ON.”
• Line-Lock: Synchronizes the unit with power frequency.
CAUTION
If the image disturbance doesn’t disappear after adjusting the PHASE dial
(
Ẇ
) on the second and subsequent cameras, adjust the PHASE dial (
Ẇ
) on
the first camera. If the problem persists, check that all the devices have
been connected with the correct power cable polarity.
Ẇ
Line phase (PHASE)
When sync setting (ẅ) is ON, use a Phillips-head screwdriver to
adjust the line phase.
ẇ
Lens iris (LEVEL)
When using a DC-type auto-iris lens, adjust the LEVEL dial if the
entire image is too dark or too bright.
Ẉ
Lens switching
Set this as appropriate for the type of lens you are using.
CAUTION
When using a video auto-iris lens
• Turn the ALC (light control) dial on the lens barrel fully to AV (average).
• If the backlight compensation is not correct, adjust the LEVEL dial on the
lens barrel.
●
●●
●
Flange-back adjustment
(only when zoom lens is attached)
Flange back is the distance between the lens and the camera
(CCD). Follow the steps below to adjust the flange back distance,
since the image can become out of focus when you are zoomed-in
on an object.
1
Loosen the LOCK screw
with a Phillips-head
screwdriver.
2
Zoom-in with the zoom
lens, and adjust the focus
with the focus ring on the
lens.
3
Set the zoom lens to wide
angle, and adjust the focus
with the flange-back adjustment dial.
4
Repeat steps 2 and 3 to check that the focus is not lost
when switching between wide-angle and zoom, and then
tighten the LOCK screw.
C
CC
C
Camera adjustment/Settings
ON Backlight compensation
OFF
★
★★
★
No backlight compensation is applied.
ON Line-Lock
• Adjust PHASE dial
Ẇ
to eliminate sync disturbance.
OFF
★
★★
★
Internal Sync
L (Low) Closes the lens iris, making the entire image darker.
H (High) Opens the lens iris, making the entire image brighter.
EI Electronic iris lens
VIDEO Video auto-iris lens (lens with built-in amp circuits)
DC
★
★★
★
DC-type auto-iris lens (lens without built-in amp circuits,
powered by DC power only)
2
1
4
LOCK
3
OBLIGATIONS
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service
Center at the user's expense, unless specifically stated otherwise in this warranty. The names and addresses of
Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below.
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES
OF AMERICA, EXCLUDING ALL U.S. TERRITORIES AND PROTECTORATES. THIS WARRANTY APPLIES ONLY
TO THE ORIGINAL RETAIL PURCHASER OR END-USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR
RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME
WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product
against defects in materials and workmanship for the periods specified below. SFC will repair or replace (at its option)
the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the
product was first purchased or rented at retail.
EXCLUSIONS
This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model's
instruction manual, or (B) the repair of any product whose serial number has been altered, defaced or removed.
This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the
product after repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including,
but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper
maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user,
abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear.
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for
it any other obligation or liability.
SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT
(INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE
FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF
THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY
DUE TO CAUSES BEYOND ITS CONTROL. SFC'S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES
RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN CONNECTION WITH THE SALE, USE OR
OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR'S NEGLIGENCE, ALLEGED DAMAGED OR
DEFECTIIVE GOODS, WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT
EXCEED THE PURCHASE PRICE OF THE PRODUCT.
ATTENTION
For your protection in the event of theft or loss of this product, please fill in the information below for you own personal
records.
SANYO INDUSTRIAL VIDEO
B/W VIDEO CAMERA LIMITED WARRANTY
For product operation, authorized service center referral, service assistance or problem resolution, call
CUSTOMER INFORMATION 1-800-421-5013
Weekdays 8:30 AM - 5:00 PM Pacific Time
For accessories and/or parts, call
PARTS ORDER INFORMATION 1-800-726-9662
Weekdays 8:30 AM - 5:00 PM Pacific Time
LABOR PARTS IMAGE DEVICE
3 YEARS 3 YEARS 3 YEARS
Model No. Serial No.
(Located on back or bottom side of unit.)
Date of Purchase Purchase Price
Where Purchased
L73R4_US.fm 2 ページ ２００３年４月２４日 木曜日 午後３時４８分