Sony XCD-V60CR/SX90CR/U100CR Digital Camera User Manual


  Open as PDF
of 2
 
English
Rear Fig. D
IEEE1394b connectors
Connect an IEEE1394b camera cable (not supplied) to this connector.
Pin No. Signal Pin No. Signal
1 TPB– 6 VG
2 TPB+ 7 NC
3 TPA– 8 VP
4 TPA+ 9 TPBG
5 TPAG
12-pin I/O connector
When power from the IEEE1394b connector is insucient, power is supplied
through this connector.
Connect a camera cable such as the CCXC-12P05N to this connector.
Pin No. Signal Pin No. Signal
1 Power GND 7 GPIO IN 2
2 Power IN 8 GPIO OUT 2-
3 ISO GND 9 GPIO OUT 2+
4 Strobe OUT 10 GPIO IN 1
5 GPIO OUT 1- 11 Trigger IN
6 GPIO OUT 1+ 12 ISO GND
Installation
Fitting the lens
Fig. E
1 Remove the lens mount cap.
2 Screw in the lens (not supplied), and turn it until it is secured.
Note
Clean the optical lter with a commercially available blower brush to remove
dust.
Using a tripod
Fig. F
To use the tripod, install the VCT-ST70I tripod adaptor (not supplied) on the
camera module.
Use a tripod screw with a protrusion (
) extending
from the installation surface, as follows:
ISO standard: Length 4.5 mm to 5.0 mm
ASA standard: Length 0.197 inches
Tighten the tripod screws using a hand screwdriver.
Note
When you install the tripod adaptor, use the screws supplied with the tripod
adaptor.
Connecting the camera cable
Fig. G
Connect a commercially available IEEE1394b camera cable to the IEEE1394b
connector and the 1394b interface connector of your PC. When you connect
the cable, insert the cable connector into the IEEE1394b connector until it snaps
into place, holding it. Then, tighten the xing screws placed on both sides of the
cable connector.
IEEE1394b connector
Fixing screws
IEEE1394b camera cable (not supplied)
Note
Loose xing screws may cause a poor connection or damage to the camera or
cable. Be sure to tighten the xing screws.
When power supply from the IEEE1394b
connector is insucient
Fig. H
Power can be supplied to the camera module via the DC-700/700CE camera
adaptor (optional) and a camera cable such as CCXC-12P05N (optional) if power
supply from the IEEE1394b connector is insucient.
12-pin I/O connector
Camera cable (e.g. CCXC-12P05N)
to AC power source
CAMERA connector
AC IN connector
Trigger generator
Controlling the Camera from Your PC
You can control the camera from your PC. The following table shows the control
functions.
Functions common to all models
Control function Description
Gain Color model 0 to +18 dB
Black and white
model
0 to +24 dB
Shutter Setting the shutter speed between 1/100,000 and 16 sec.
Brightness Pedestal level adjustable
Gamma Customizing the gamma curve using 1,024 gamma tables
(10 bits) (IIDC extended function)
Trigger Mode 0 (control by register) and Mode 1 (control by pulse
width) supported for hardware trigger/software trigger
Broadcast commands supported for software trigger
Strobe Out Setting the delay from the exposure start and the pulse
width by register value
AutoExposure Keeping a constant average image level by the image
level detection and feedback to gain and shutter
AutoExposure
Detection Frame
Setting
Setting the detection area for Auto Exposure
GPIO Assigning GPIO (General-Purpose Input/Output) to the
12-pin connector
MemoryShot Saving an image to the built-in frame memory and
reading the saved image from the memory
ISO Enable (Video
Start)
Starts transmitting an image in continuous mode
OneShot/
MultiShot
OneShot Transmitting an image
MultiShot
Transmitting the specied number of
images
DataDepth Indicating the eective bit length in 16-bit mode
CameraInitialize Resetting the camera to the default features
MemoryChannel PresetMemory0 (factory default status) and 1 user
available memory channel / 15 user available memory
channels selectable
1394 Bus
Synchronization
Dening the exposure timing in synchronization with
the cycle time register of 1394 bus
TriggerDelay Specifying the delay time after which the received
trigger becomes eective
PartialScan Partition by a unit of 32 lines x 24 pixels available
UserFreeMemory A 256-byte user available memory provided
Bulk Mode Acquiring images continuously by changing the settings
in memory channels
日本語
D
IEEE1394b
端子
IEEE1394b
ピン番号 信号 ピン番号 信号
1 TPB 6 VG
2 TPB 7 NC
3 TPA 8 VP
4 TPA 9 TPBG
5 TPAG
12
ピン
I/O
コネクター端子
IEEE1394b
CCXC-12P05N
ピン番号 信号 ピン番号 信号
1 ( ) 7 GPIO 2
2 8 GPIO 2
3 ISO( ) 9 GPIO 2
4 10 GPIO 1
5 GPIO 1 11
6 GPIO 1 12 ISO( )
E
1
2
ご注意
F
VCT-ST70I
ISO
4.5mm 5.0mm
ASA
0.197
ご注意
G
IEEE1394b IEEE1394b 1394b
IEEE1394b
IEEE1394b
ご注意
IEEE1394b
H
IEEE1394b DC-
700( ) CCXC-12P05N
12 I/O
CCXC-12P05N
AC
CAMERA
AC IN
全モデル共通機能
制御項目 内容
0 +18 dB
0 +24 dB
1
/
100,000
16
1024 10
IIDC
/
Mode0( ) Mode1( )
GPIO 12 GPIO
ISO Enable(
)
OneShot/MultiShot OneShot 1
MultiShot
DataDepth 16
CameraInitialize
PresetMemory0( )
1 ch/15 ch
1394 1394
32 x 24
256
XCD-V60CR/SX90CR/U100CR(
カラーモデル
)
のみ
制御項目 内容
Raw R B
/
G G
XCD-V60/SX90/U100(
白黒モデル
)
のみ
制御項目 内容
3 x 3 3 x 3
IEEE1394 Ver.1.31
IT CCD
XCD-V60CR/V60/SX90CR/SX90: 1/3
XCD-U100CR/U100: 1/1.8
IEEE1394b – 2002
( )
XCD-V60CR/V60: 640 x 480 (VGA)
XCD-SX90CR/SX90: 1,280 x 960 (SXGA)
XCD-U100CR/U100: 1,600 x 1,200 (UXGA)
XCD-V60CR/V60: 90 fps
XCD-SX90CR/SX90: 30 fps
XCD-U100CR/U100: 15 fps
800/400 Mbps
( )
10 s
DC 5 24V
C
17.526 mm
XCD-V60CR/SX90CR/U100CR: 20 lx (F1.4 Gain:
+18 dB)
XCD-V60/SX90/U100: 2 lx (F1.4 Gain: +24 dB)
= 1 LUT
XCD-V60CR/SX90CR/U100CR: 0 +18 dB
XCD-V60/SX90/U100: 0 +24 dB
1/100,000 16
IEEE1394b 12
DC +8 V +30 V
XCD-V60CR/V60/SX90CR/SX90: 2.8 W DC 12V
XCD-U100CR/U100: 3.0 W DC 12V
0 +40
5 45
30 60
20 80 ( )
20 95 ( )
10G (20Hz 200Hz )
70G
44 (W) 33 (H) 57.5 (D)mm
140g
(1)
(1)
XCD-V60CR/SX90CR/U100CR (color models) only
Control function Description
WhiteBalance (Raw
mode)
Adjusting the R and B levels individually
Auto white balance, One Push white balance available
G Gain Adjusting the G gain
OpticalFilter Switching the Bayer pattern
XCD-V60/SX90/U100 (black and white models) only
Control function Description
3 x 3 Filter Switching the 3 x 3 lter
Sharpness Adjusting the image contour strength
These control items comply with Digital Camera Protocol, Ver. 1.31, of the IEEE1394 Standard.
For more details, refer to the Technical Manual.
Specications
Pickup device Progressive scan IT CCD
XCD-V60CR/V60/SX90CR/SX90: 1/3 type
XCD-U100CR/U100: 1/1.8 type
Interface IEEE1394b – 2002
Output signal format (horizontal/vertical)
XCD-V60CR/V60: 640 x 480 (VGA)
XCD-SX90CR/SX90: 1,280 x 960 (SXGA)
XCD-U100CR/U100: 1,600 x 1,200 (UXGA)
Frame rate XCD-V60CR/V60: 90 fps
XCD-SX90CR/SX90: 30 fps
XCD-U100CR/U100: 15 fps
Transfer speed 800/400 Mbps
External trigger signal (conditions)
Pulse width: 10 μs or more
Polarity: Negative
Amplitude: 5 to 24 V DC
Lens mount C-mount
Flange back 17.526 mm
Minimum illumination XCD-V60CR/SX90CR/U100CR: 20 lx (F1.4, Gain: +18
dB)
XCD-V60/SX90/U100: 2 lx (F1.4, Gain: +24 dB)
Gamma γ= 1 (selectable by LUT)
Gain XCD-V60CR/SX90CR/U100CR: 0 to +18 dB, Auto
gain
XCD-V60/SX90/U100: 0 to +24 dB, Auto gain
Shutter speed 1/100,000~16 seconds, Auto shutter
Power +8 V to +30 V DC from IEEE1394b camera cable or
camera cable with 12-pin connector
Power consumption XCD-V60CR/V60/SX90CR/SX90: 2.8 W (12 V DC
input)
XCD-U100CR/U100: 3.0 W (12 V DC input)
Performance guaranty temperature
0 to +40°C (32 to 104°F)
Operating temperature –5 to +45°C (23 to 113°F)
Storage temperature –30 to +60°C (–22 to 140°F)
Operating relative humidity
20 to 80% (no condensation)
Storage relative humidity 20 to 95% (no condensation)
Vibration resistance 10 G (20 Hz to 200 Hz, at using the reference holes)
Shock resistance 70 G
External dimension (w/h/d) 44 × 33 × 57.5 mm (1
3
/
4
× 1
3
/
16
× 2
3
/
8
inches), not
including projecting parts
Mass 140 g (4 oz)
Accessories Lens mount cap (1)
Operating Instructions (1)
Design and specications are subject to change without notice.
IMPORTANT
The nameplate is located on the bottom.
Note
Always verify that the unit is operating properly before use. SONY WILL
NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED
TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF
PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER
DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY,
OR FOR ANY OTHER REASON WHATSOEVER.
Regular parts replacement
Some of the parts that make up this product (electrolytic condenser, for
example) need replacing regularly depending on their life expectancies.
The lives of parts dier according to the environment or condition in which
this product is used and the length of time it is used, so we recommend
regular checks.
Consult the dealer from whom you bought it for details.
About the Technical Manual
The Operating Instructions describe the functions and use of this product.
For more details, see the
Technical Manual
. Please ask your sales
representative about the
Technical Manual
.
重要
VCCI
A
定期交換部品について
 previous