Filter
Top Products
- 6 -
3. INSTALLATION
Notes:
The attached screws and anchors are used to install the camera to a solid •
surface. (e.g. concrete) If installing to loose or thin material surfaces , use
the appropriate anchors (not included) with the screws.
Install the camera tightly.•
3-1 Mounting the camera to a solid surface
(1) Attach the Alignment Sticker to the surface.
(2) Drill three pilot holes (Ø0.28inch×1.57inches(D)(Ø7mm×40mm(D)))
through the three circles on the sticker.
(3) Hammer the supplied plastic anchors into the holes.
(4) Drill a hole (Ø0.63inch(Ø15mm) in the center of the sticker, and lead the
video and power cables in this hole.
(5) Align the three holes of the Mounting Bracket with the three plastic anchors;
insert the supplied screws with camera to corresponding holes.
3-2 Adjusting the view angle and lens
(1) The camera direction can be adjusted horizontally (pan: max. 360 deg.)
and vertically (tilt: max. 90 deg.).
(2) To adjust pan and tilt rotate the Clamp Ring counterclockwise, and loosen
the two Locking Screws using a screwdriver.
Alignment Sticker
Anchor
Clamp Ring
Screw
Locking Screw
1. Replace original screw
by hexagonal screw
of accessories, and
temporarily fix it.
2. Adjust the shade to the
best position.
3. Secure this screw by
using a wrench (not
included).
- 7 -
(3) Turn the camera to the desired position, rotate the Clamp Ring clockwise to
secure the camera.
(4) To adjust zoom and focus, loosen two controller screws, and move them to
the desired position.
(5) Tighten zoom and focus controller screws. To secure these screws tightly,
be sure to tighten them using a screwdriver.
(6) To secure the camera tightly, be sure to tighten the two Locking Screws
using a screwdriver.
Note:
Adjust the shade position after replacing original screw by hexagonal screw •
of accessories.
Be sure to securely tighten the Clamp Ring.•
3-3 Adjusting the BLC and AGC
AGC and BLC selecting switches are internally-located.To adjust these
switches, rotate the cap counterclockwise. After adjusting, rotate the cap
clockwise. Make sure that the cap has been tightly secured to the camera using
a screwdriver.
(1) Backlight Compensation (BLC)
The exposure is automatically adjusted so that the best picture is obtained
at a monitor zone of about 50% in the horizontal and about 50% in the
vertical directions. The factory setting is "ON".
(2) Auto Gain Control (AGC)
Camera maximum gain can be selected High (30dB) or Low (24dB). The
factory setting is "High". If the image is noisy in low-light, change this switch
to "Low".
3-4 Day / Night Function
This camera is equipped with near-infrared LEDs (IR LED) of 850nm. The LEDs
turn on automatically when it becomes dark. (The human eye cannot clearly
see the light of the LEDs.)
This camera is able to clearly produce monochrome images at a range of less than
82 feet.
- 8 -
4. NOTES ON USE AND INSTALLATION
Do not aim the camera at the sun•
Never aim the camera at the sun even with the camera power off.
Do not shoot intense light•
Intense light such as a spotlight may cause a bloom or smear. A vertical stripe
may appear on the screen. However, this is not a malfunction.
Treat the camera with care•
Do not drop the camera or subject it to intense vibration.
Never touch internal parts•
Do not touch the internal parts of the camera other than the parts specified.
Do not submerge in water•
Install the camera where the camera can be used indoors or outdoors according
to IP66 code. If the camera was dropped in the water, turn off the power and
contact your dealer.
Keep the camera installation away from video noise•
If cables are wired near electric lighting wires or a TV set, noise may appear in
images. In this event relocate cables or reinstall equipment.
Check the ambient temperature and humidity•
Avoid using the camera where the temperature is hotter or colder than the
specified operating range. Doing so could affect the internal parts or cause the
image quality to deteriorate. Special care is required to use the camera at high
temperature and humidity.
Should you notice any trouble•
If any trouble occurs while you are using the camera, turn off the power and
contact your dealer. If you continue to use the camera when there is something
wrong with it, the trouble may get worse and an unpredictable problem may occur.
5. IN CASE OF PROBLEMS
Condition Check Points
No image • Are the camera and connected equipment turned on?
• Are wires connected correctly?
Unnatural color • Is the display monitor adjusted correctly?
• Is the lighting too dim?
Flicker noise • Under the uorescent lamp of 60Hz, icker noise rarely occurs.
Defocusing at night • Readjust the focus at night-mode that turned on the IR LED.
- 9 -
6. SPECIFICATIONS
1. Image System
Image Device 1/3 inch CCD image sensor
Pixel Elements 768 (H) x 494 (V)
2. Electrical
TV System NTSC
2:1 Interlace, 15.734 kHz horizontal, 59.94 Hz vertical
Horizontal Resolution 480 TV lines (typical)
S/N Ratio 48 dB
Minimum Illumination 0 lux (LED is ON)
Gain Control AGC:High (30dB), Low(24dB)
White Balance Auto
White Balance Range 2,500 K to 9,500 K
Auto Electronic Shutter 1/60 s to 1/100,000 s
Backlight Compensation (BLC)
ON / OFF
Video Output Signal VBS (1.0 Vp-p, 75 ohms unbalanced, BNC)
Synchronization System Internal
IR LED 36 LEDs, 850nm
IR Distance 82 feet (25m)
3. Mechanical
Weight 1.4 lbs (630 g) camera only
Dimension 3.2(W) x 3.1(H) x 5.4(D) inches (81.5mm(W) x 79.5mm(H)
x 137.5mm(D) (excluding protrusion and mounting bracket))
Ingress Protection Rating IP66
4. Optical
Built-in Lens f = 3.7-10 mm, F 1.6
View Angle of Lens 27-77°(H), 21-57°(V)
5. Power
Input Voltage 12V DC ±10 %
Current Consumption 0.4A (MAX.)
- 10 -
6. Environmental
Operating Temperature
and humidity
14°F to 122°F (-10°C to +50°C )
20 % to 90 % RH
Storage Temperature
and humidity
-4°F to 140 °F (-20°C to 60°C)
90 % RH
Design and specifications are subject to change without notice.
7. EXTERIOR VIEW
120°
120°
Ø2.4 Ø62
3-Ø0.2 Ø5
1 25
2.1 54
0.24 6
4.2 106
3.2 81.5
Ø2.8 Ø70
5.4 137.5
3.1 79.5
Dimensions: Inch (mm)
- 11 -
LIMITED WARRANTY
CCD SECURITY CAMERA IK-7200A
The Imaging System Division (“ISD”) of Toshiba America Information Systems,Inc.makes the following limited warranties with regard to this
CCD Camera Model IK-7200A (“Product”).These limited warranties extend to the Original End-User (“You [r]”).
Three (3) Year Limited Warranty of Labor and Parts ISD warrants that this Product will perform in accordance with specifications for a
period of three (3) years from the date of purchase by the Original End-User. During this three (3) year period, ISD will repair or replace the
Product, if it does not perform as warranted. In order to take advantage of this Limited Warranty. You must: (a) call (877) 855-1349 to receive a
RMA number:and (b) pay all transportation and insurance charges for shipment of the Product to the ASP or Toshiba Exchange Center. ISD
reserves the right to substitute factory refurbished parts in place of those in need of repair.
Instruction Manual (Owner's Manual) :You should read the Instruction Manual (Owner's Manual) thoroughly before operating this Product.
Before seeking warranty service, you should check the troubleshooting guide in the Instruction Manual (Owner's Manual) and follow the
instructions to correct the problem.
How to Obtain Warranty Service Step-by-step Procedures :To obtain warranty service. You should :
1. Contact Toshiba America Information Systems, Inc. at (877) 855-1349 to first verify operation or installation assistance. (877) 855-1FIX
2. If technical support determines that the unit is defective,an RMA will be issued with return instructions for repair.
3. Securely pack the Product in the original carton and external shipping pack, include a letter explaining the problem with a copy of the bill of
sale or proof of purchase.
4. Prepay all transportation and insurance costs.
Your Responsibilities: This Limited Warranty is subject to the following conditions:
1. You must provide the bill of sale or proof of purchase at the time that warranty service is required.
2. You must notify Toshiba America Information Systems, Inc. at (877) 855-1349 within (30) days after you discover that the product does not
perform in accordance with specifications during the Limited Warranty period.
3. You must pack the Product in its original carton using the original packing material.Then insert the original carton containing the Product
into another carton with additional packing material before shipping the Product to an ASP or Toshiba Exchange Center.
DISCLAIMERS: ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO NOT ALLOW
THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE
THE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT COMPANY OR ANY ASP BE LIABLE
TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION
APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR
OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF CONTRACT, TORT OR
OTHERWISE, OR WHETHER ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF TAIS, ITS PARENT
COMPANY, OR AN ASP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR SOME
PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE
TO STATE.
THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE, ABUSE, ACCIDENT,
IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION OF ISD'S WRITTEN INSTRUCTIONS, OR WHERE THE
PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD'S PRIOR AUTHORIZATION, OR UPON THE REMOVAL OR ALTERATION
OF ISD'S FACTORY SERIAL NUMBER. LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT OF
CONTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY.
No person, agent, distributor,dealer,authorized service provider, or company is authorized to change, modify, or extend the terms of this
Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce any obligation of ISD arising
under this Limited Warranty or under any statute, or law of the United States or any state thereof, is herby limited to one (1) year from the date
You discovered or should have discovered the problem. This limitation does not apply to implied warranties arising under state law.
Some states do not permit limitation of the time within which You may bring an action beyond the limits provided by state law, so the above
provision may not apply to You. This Limited Warranty gives You spacific legal rights and You may also have other rights which vary from state
to state.
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
Imaging Systems Division