C-1
ACCESSORIES
C-1
OPTIONAL EQUIPMENT (Field Installed)
K957-1 Heavy Duty, Two Wheel Trailer For Small
Welders - For road, off-road and in-plant and yard
towing. (For highway use, consult applicable federal,
state and local laws regarding requirements for
brakes, lights, fenders, etc.)
Order K957-1 Trailer
K958-1 Ball Hitch
K958-2 Lunette Eye Hitch
K959-2 Fender & Light Kit
K965-1 Cable Storage Rack
K889-2 & -3 Two-Wheel Undercarriage - For moving
by hand. Overall Width 29in.(.74m). Both have pneu-
matic tires. Puncture proof tires included with K889-3.
K1737-1 Four Wheel All-Terrain Undercarriage -
For moving by hand at construction sites. Heavy duty
puncture resistant pneumatic tires.
K1770-1 Undercarriage (Factory) - For moving by
hand on a smooth surface. One or two gas cylinders
can be mounted on the rear of the undercarriage with
the installation of K1745-1 Cylinder Holder(s). Heavy
duty puncture resistant pneumatic tires and front cast-
er.
K1745-1 Welding Gas Cylinder LPG Tank Holder -
Holds Welding Gas Cylinder for use on K1770-1
Undercarriage. One or two may be installed on an
undercarriage.
K1788-1 Roll Cage - Gives added damage protection.
Attaches to K1737-1, K1770-1, and K957-1.
K886-1 Canvas Cover -To protect the WELDMARK
225 when not in use. Made from attractive red canvas
material which is flame retardant, mildew resistant,
and water repellent.
K802R Power Plug Kit- provides four 120V plugs
rated at 15 amps each and one dual voltage, Full
KVA plug rated at 120/240V, 50 amps.
K802N Power Plug Kit - Provides four 120V plugs
rated at 20 amps each and one dual voltage, full KVA
plug rated at 120/240V, 50 amps.
K704 Accessory Kit - For Stick welding. Includes 35 ft
(10.7m) 2/0 AWG electrode cable, 30 ft. (9.1m) 2/0 AWG
work cable with lugs, headshield, Filter plate, work clamp
and electrode holder. 400 amp capacity.
K875 Accessory Kit - For Stick welding. Includes 20 ft
(6.1m) #6 electrode cable with lugs, 15 ft. (4.6m) #6 work
cable with lugs, headshield, Filter plate, work clamp and
electrode holder and sample pack of mild steel electrode.
150 amp capacity.
K894-1 Spark Arrester Kit - Includes a heavy gauge steel,
approved spark arrester and clamp for easy mounting to
muffler exhaust pipe.
K1690-1 GFCI Receptacle Kit - Includes one UL
approved120V ground fault circuit interrupter duplex type
receptacle with cover and installation instructions.
Replaces the factory installed 120V duplex receptacle.
Each receptacle of the GFCI Duplex is rated at 20 Amps,
the maximum total current from the GFCI Duplex is limit-
ed to the 20 Amps. Two kits are required.
K1816-1 Full KVA Adapter Kit - Plugs into the 120/240V
NEMA 14-50R receptacle on the case front (which accepts
4-prong plugs) and converts it to a NEMA 6-50R receptacle,
(which accepts 3-prong plugs.)
T12153-9 Full-KVA Power Plug - One dual voltage plug
rated at 120/240V, 50 amps.
K930-2 TIG Module - Provides high frequency and shield-
ing gas control.for AC and DC GTAW (TIG) welding applica-
tions. Its compact case is designed foe easy carrying, com-
plete with a handle. High frequency bypass is built in.
Requires K938-1 Contactor Kit, K936-4 Control Cable, and
K814 Arc Start Switch.
K938-1 Contactor Kit - For use with TIG Module, Provides
a “cold” electrode until the triggering device (Arc Start
Switch) is pressed.
K936-4 Control Cable - Connects TIG Module to Weldmark
225.
K814 Arc Start Switch - Attaches to the TIG torch for con-
venient finger control.
K937-45 Control Cable Extension - Allows TIG Module to
be operated at distances up to 200ft. from the power source.
Available in 45ft. (13.7m).
K939-1 Docking Kit - For Mounting the K930-2 TIG Module
on top of the Weldmark 225.
WELDMARK 225
