!
!
!
!
!
!
!
RadioShack’s patented 6-channel radio controller allows you to change
your racing frequency on the fly when you compete in multi-car races.
Light up the race track with your ZipZaps headlights.
Improved control with a digital proportional radio controller.
Everything you need to assemble your own racing machine is included.
Leave the pit quickly with a quick charge time of about 60 seconds.
Carry your 1:64 scale tunable ZipZaps in your pocket.
ZipZaps provide great fun for ages 8 and up.
To really rev up the fun factor, customize your ZipZaps micro RC with
optional performance upgrade kits,viewable at the ZipZaps Showroom at
and available at your local RadioShack.
Follow these simple steps to make your ZipZaps race ready.
www.zipzaps.com
EXPERIENCE THE ULTIMATE MICRO
RADIO CONTROL EXCITEMENT!
EXPERIENCE THE ULTIMATE MICRO
RADIO CONTROL EXCITEMENT!
1. Align the tabs on the HUBCAPS with the
notches in the front axle wheels,and then
stretch theTIRES over the HUBCAPS.
2. Install the MOTORWITH DRIVE GEAR in the
groove on the back of the CHASSIS.
3. Carefully hook the MOTOR CLIP onto
theTRANSFER GEARAXLE and swing
the MOTOR CLIPWITH SET SCREW flat
against the chassis.
4. Tighten the SET
SCREW in the
MOTOR CLIP using
the SCREWDRIVER
5. Push theTRANSFER GEAR onto the
axle as shown. Be sure the
TRANSFER GEAR meshes with the
DRIVE GEAR on the STOCK MOTOR.
6. Align the tabs on the HUBCAPS with the
notches in the REARAXLE,and then stretch
theTIRES over the HUBCAPS.
7. Snap the REARAXLE
GEAR assembly to the
CHASSIS as shown. Be
sure the REARAXLE
GEAR meshes with the
TRANSFER GEAR.
stored in the
bottom of the CONTROLLER.
1
2
8. Plug the LED
connector of the
car top into the
male
connector on the
.
9. Thread theANTENNA
through the hole in
the BODYTOP.
10. Place the tab at the
rear of the CHASSIS
into the slot on the
rear of the BODYTOP.
Secure the BODYTOP by gently pushing the
BODYTOP onto the CHASSIS until the
CHASSIS’ front tab clicks into the front slot of
the BODYTOP as shown.
car chassis’
circuit board
as shown
EXPERIENCE THE ULTIMATE MICRO
RADIO CONTROL EXCITEMENT!
EXPERIENCE THE ULTIMATE MICRO
RADIO CONTROL EXCITEMENT!
EXPERIENCE THE ULTIMATE MICRO
RADIO CONTROL EXCITEMENT!
1. The CONTROLLER charges your micro RC and controls its steering and speed.You’ll need
to install fourAAA batteries (not supplied).The ZipZaps factory recommends RadioShack
Enercell Plus alkaline batteries.
2. Turn off the controller.
3. Remove the battery compartment cover and battery holder.
4. Insert theAAA batteries by matching polarity markings and then
insert battery holder.
5. Replace the cover and snap shut.
Your ZipZaps micro RC Starter Kit includes everything you see here:
1
Starter Kit Includes
2
Power Up Your Controller
1. Turn on the CONTROLLER.The LED lights green.
2. Turn on your ZipZaps micro RC.
3. Open the cover on top of the CONTROLLER. Point
your car to the left and align the metal contacts
underneath the car with the metal contacts on top
of the CONTROLLER until your car clicks into place.
4. To change the racing channel of your micro RC,
select one of the six channels on the front left side
of the CONTROLLER, while t
5. When the channel has been successfully changed,
the LED stops blinking and charging begins until
complete.If programming fails, the LED turns
amber.Detach your car to clear the failed
programming.After verifying you turned your micro
RC on, place it back on the CONTROLLER until
programmed and fully charged.
6. The LED turns green after your micro RC has been
fully charged.
Press RELEASE to unlock the micro RC.
he LED blinks red.You
have about 10 seconds to change channels before
charging begins.
OPEN
1
2
4
Zap It On the Charger
For optimum racing conditions drive on a smooth, flat
surface.
Open the removable cover on top of the CONTROLLER.
Fully extend the antenna.Turn the CONTROLLER on.The
ON/OFF LED lights green.
Trigger Control
Designed for easy operation with
either hand, you can reverse the
direction of the throttle control
using the left/right switch on the
top of the CONTROLLER. If you hold
the CONTROLLER in your right
hand, set the switch to R and your
micro RC moves forward as you pull
the trigger left and moves
backward as you push the trigger
right.
If you hold the CONTROLLER in
your left hand, set the switch to L
and your micro RC moves forward
as you pull the trigger right and
moves backward as you push the
trigger left.
Release the trigger to the center
position to stop your Micro RC. If it
continues to move,see Performance
Adjustments.
Roll the steering knob left to turn
left, right to turn right,and release
to go straight.
Steering Control
5
Zoom Away
Caution: Do not overtighten
set screw causing MOTOR
CLIP to angle away from
chassis.MOTOR CLIP should
be horizontal to chassis.
Caution: Always use RELEASE when
removing the car from the charger.
Battery Notes
!
!
!
!
!
Use only fresh batteries of the required size and recommended type.
Do not mix old and new batteries,different types of batteries (standard, alkaline,or rechargeable),
or rechargeable batteries of different capacities.
If you do not plan to use your micro RC for a week or more,remove all the batteries from the
CONTROLLER to prevent leaks that can damage electronic parts.
Never leave dead or weak batteries in your CONTROLLER.
Dispose of dead batteries promptly and properly; do not burn or bury them.
When your batteries are too weak to charge your car,the LED remains green after the frequency has been
programmed, followed by the LED alternating red and green.Replace the batteries in your CONTROLLER.
3
Zip Your Car
0
5
25
75
95
100
0
5
25
75
95
100
0
5
25
75
95
100
0
5
25
75
95
100
ZipZaps2 manual p1 7-7.prn
S:\010087\010087Pub\Project\600\ZipZaps 2.0\ZipZaps2 manual.cdr
Monday, July 07, 2003 2:37:05 PM
Color profile: Generic CMYK printer profile
Composite Default screen
