© Titan Tool Inc. All rights reserved. 5
PowrTex 12000 SF Gas Sprayer
Gallons per minute (GPM) ............. 3.15 (11.9 LPM)
Cycle rate per gallon......................38 (10.5 cycles/liter)
Maximum tip sizes .........................1 gun = .058”
2 guns = .040”
3 guns = .034”
4 guns = .030”
5 guns = .026”
6 guns = .024”
Maximum pressure ........................3300 PSI (22.8 MPa)
Power .........................................8 HP, 4-stroke, single
cylinder, overhead valve
engine w/oil alert
Fuel capacity .................................1.4 US gallons
(approx. 2.5 hours run time)
Halogenated solvent compatible ...Yes
Weight .........................................183 lbs. (83 kg.)
Inlet paint lter ...............................10 mesh “Rock Catcher”
Outlet paint lter ............................50 mesh, 18 in.
2
Pump inlet......................................1” NPT(F)
Pump outlet ...................................1/2” NPT(F) to paint lter
Paint lter hose connections..........1/4” NPS(M)
3/8” NPT(F) (plugged)
3/8” NPT (plugged)
Dimensions .................................... 46” L (116.8 cm) x
27” W (68.6 cm) x
34” H (86.6 cm)
Fluid section wetted parts:
Electroless nickel plated ductile iron, electroless nickel plated
carbon steel, stainless steel, tungsten carbide, Teon, thiokol
impregnated leather, ultra high molecular weight polyethylene.
PowrTex 12000 SF Electric Sprayer
Gallons per minute (GPM) ............. 1.25 (4.7 LPM)
Cycle rate per gallon......................55 (14.5 cycles/liter)
Maximum tip sizes .........................1 gun = .036”
2 guns = .026”
3 guns = .019”
Maximum pressure ........................3300 psi (22.8 MPa)
Power .........................................2 HP DC Motor, 115V 15.5A,
overload protected
Halogenated solvent compatible ...Yes
Weight .........................................165 lbs. (74.8 kg.)
Inlet paint lter ...............................10 mesh “Rock Catcher”
Outlet paint lter ............................50 mesh, 18 in.
2
Pump inlet......................................1” NPT(F)
Pump outlet ...................................1/2” NPT(F) to paint lter
Paint lter hose connections..........3/8” NPS(M)
3/8” NPT(F) (plugged)
1/4” NPT (plugged)
Dimensions .................................... 43” L (109 cm) x
26” W (66 cm) x
35” H (89 cm)
Fluid section wetted parts:
Electroless nickel plated ductile iron, electroless nickel plated
carbon steel, stainless steel, tungsten carbide, Teon, thiokol
impregnated leather, ultra high molecular weight polyethylene.
Introduction
Congratulations on having selected the nest airless sprayer
available in the world! These airless sprayesr are precision
power tools used for spraying many types of materials including
textured products from a ready-mixed or powdered formulation.
Read and follow this instruction manual carefully for proper
operating instructions, maintenance, and safety information.
Motor/Pump
Assembly
Outlet Fitting
Bleed Valve
Hydraulic
Fluid Cap/
Dipstick
Pressure
Control
Knob
Gas
Tank
Spray
Gun w/
Splatter
Nozzle
Pressure
Gauge
Bleed Hose
Hydraulic
Shut-Off
Valve
Motor/Pump
Assembly
Outlet Fitting
Bleed Valve
Hydraulic
Fluid Cap/
Dipstick
Pressure
Control
Knob
Gas
Tank
Spray
Gun w/
Splatter
Nozzle
Pressure
Gauge
Shovel
Valve
Bleed Hose
Hydraulic
Shut-Off
Valve
NOTE: These sprayers come with a heavy duty bleed
valve installed in place of the lter assembly.
Use this heavy duty bleed valve when spraying
textured products from a ready-mixed or
powdered formulation. A lter assembly that
includes a standard bleed valve can be installed
on the sprayer when spraying standard materials.
To install the lter assembly, remove the heavy
duty outlet assembly from the swivel tting on
the motor/pump assembly and install the lter
assembly in its place. Refer to the Maintenance
and Parts List sections of this manual for more
information on the lter assembly.
