Specifications
Liters per minute (LPM) ...................1.5 (0.40 GPM)
Maximum tip sizes ...........................0.019”
Maximum pressure ..........................20.6 MPa (3000 PSI)
Power, 230V unit..............................3/4 HP DC motor, 230V,
50/60 HZ, 4.5 AMP,
1035W
Power, 110V unit..............................3/4 HP DC motor, 110V,
50/60 HZ, 8.8 AMP,
1035W
Weight..............................................15.4 kg (34 lbs.)
Maximum hose length......................91.4 m (300’)
Maximum power cord length............91.4 m (300’)
General Description
This airless sprayer is a precision power tool used for spraying
many types of materials. Read and follow this instruction
manual carefully for proper operating instructions,
maintenance, and safety information.
Operation
This equipment produces a fluid stream at extremely high
pressure. Read and understand the warnings in the
Safety Precautions section at the front of this manual
before operating this equipment.
Setup
Perform the following procedure before plugging in the power
cord of an electric unit.
1. Ensure that the suction set and the return hose are
attached and secure.
2. Using a wrench, attach a minimum of 15m (50’) x 10mm
(1/4”) nylon airless spray hose to the unit. Tighten
securely.
3. Attach an airless spray gun to the spray hose. Using two
wrenches (one on the gun and one on the hose), tighten
securely.
Make sure all airless hoses and spray guns are electrically
grounded and rated for at least 23 MPa (3300 PSI) fluid
pressure.
NOTE: Do not attach the tip to the spray gun yet.
Remove the tip if it is already attached.
ON/OFF
Switch
Oil Cup
Outlet
Fitting
Fluid
Section
Pressure
Control
Knob
Siphon
Hose
Motor
Return
Tube
Liquid
Holder
and
Drip Cup
PRIME/
SPRAY
Valve
Circuit
Breaker
4 © Titan Tool Inc. All rights reserved.
4. Make sure the pressure control knob is turned fully
counterclockwise to its minimum setting.
5. Make sure the ON/OFF switch is in its OFF position.
6. Fill the oil cup with 15g (one tablespoon) of piston seal
lubricant (Piston Lube).
Never operate unit for more than ten seconds without
fluid. Operating this unit without fluid will cause
unnecessary wear to the packings.
7. Make sure the electrical service is correct for the unit.
8. Plug the power cord into a properly grounded outlet at
least 7.6m (25’) from the spray area.
Always use a minimum 12 gauge, three-wire extension cord
with a grounded plug. Never remove the third prong or use
an adapter
.
Preparing a New Sprayer
If this unit is new, it is shipped with test fluid in the fluid section
to prevent corrosion during shipment and storage. This fluid
must be thoroughly cleaned out of the system with mineral
spirits before you begin spraying.
Always keep the trigger lock on the spray gun in the
locked position while preparing the system.
1. Place the suction tube into a container of mineral spirits
that has a flash point of 60ºC (140ºF) or above.
2.
Place the return hose into a metal waste container.
3. Set the pressure to minimum by turning the pressure
control knob fully counterclockwise.
4. Move the PRIME/SPRAY valve down to the PRIME
position.
5. Turn the unit on by moving the ON/OFF switch to the ON
position.
6. Allow the sprayer to run for 15–30 seconds to flush the
test fluid out through the return hose and into the waste
container.
7. Turn the unit off by moving the ON/OFF switch to the OFF
position.
Preparing to Paint
Before painting, it is important to make sure that the fluid in the
system is compatible with the paint that is going to be used.
Always keep the trigger lock on the spray gun in the
locked position while preparing the system.
1. Place the suction tube into a container of the appropriate
solvent for the material being sprayed (refer to
recommendations of the material manufacturer). An
example of the appropriate solvent is water for latex paint.
2.
Place the return hose into a metal waste container.
3. Set the pressure to minimum by turning the pressure
control knob fully counterclockwise.
4. Move the PRIME/SPRAY valve down to the PRIME
position.
5. Turn the unit on by moving the ON/OFF switch to the ON
position.
NOTE: Incompatible fluids and paint may cause the
valves to become stuck closed, which would
require disassembly and cleaning of the
sprayer’s fluid section.
