A SERVICE OF

logo

Open as PDF
next previous
English
2 © Titan Tool Inc. All rights reserved.
Using the Gun Trigger Lock
Trigger locked
(gun will not spray)
Trigger unlocked
(gun will spray)
Alwaysengagethegun’s
triggerlockwhenthegunis
notinuse.
1. Tolockthetrigger,
rotatethetriggerlock
forwarduntilitstops.
2. Tounlockthetrigger,
rotatethetriggerlock
backwarduntilitis
vertical.
Setup
Never attempt to assemble, change, or clean the gun, tip,
or tip guard without first relieving pressure from the spray
system. Follow the “Pressure Relief Procedure” in the
sprayer’s Owner’s Manual.
Always use a tip safety guard for added protection against
injection. Beware that the guard alone will not prevent
injection. Never cut off tip guard! Always engage gun
trigger lock when the gun is not in use. Before servicing
equipment, consult Owner’s Manuals and follow all
warnings.
1. Setupthesprayer.Refertotheinstructionsinthesprayer’s
Owner’sManual.
2. Attachagrounded,airlesssprayhosetothematerialinletonthe
gun.Usingtwowrenches(oneonthegunandoneonthehose),
tightensecurely.
3. Withthetipandtipguardoffthegun,startthesprayer.Flush
andpreparethespraysystemaccordingtothesprayer’sOwner’s
Manual.Inspectthespraysystemtomakesurethatallttings
aresecureandthattherearenoleaks.
Tip Seal
Seal
Tip
Tip
Guard
4. Performthe“PressureRelief
Procedure”describedinthesprayer’s
Owner’sManual.
5. Usingapenorsimilarobject,insert
thetipsealandsealintotheback
ofthetipguard.Pressinfornal
adjustment.
6. Insertthetipintotheslotonthetip
guard.
7. Threadthetipguardontothegun.
Positionthetipguardinthedesired
sprayingposition,thentighten
securelybyhand.
NOTE: The arrow on the tip handle should be pointing in the
forward direction for spraying.
Operation
1. Makesurethearrowonthetiphandleispointingintheforward
directionforspraying.
2. Startthesprayer.Refertotheinstructionsinthesprayer’s
Owner’sManual.
3. Adjusttheuidpressureonthesprayeruntilthesprayis
completelyatomized.Alwayssprayatthelowestpressure
necessarytogetthedesiredresults.
NOTE: The spray tip determines the size of spray pattern
and coverage. When more coverage is needed, use a
larger tip instead of increasing uid pressure.
4. Toclearacloggedtip:
a. Rotatethetip180ºsothatthearrowonthetiphandleis
pointingoppositethespraydirection.
b. Triggerthegunoncesothatthepressurecanblowtheclog
out.
IMPORTANT: Never pull the trigger more than once at time with the
tip in the reverse position.
c. Continuethisprocedureuntilthetipisclearoftheclog.
Changing a Tip
Tipscanberemovedandreplacedeasilywithoutdisassemblingthegun.
Never attempt to change or clean the tip or tip guard
without first performing the “Pressure Relief Procedure.”
1. Performthe“PressureReliefProcedure”describedinthe
sprayer’sOwner’sManual.
2. Removethetipfromtheslotonthetipguard.
3. Insertthenewtipintotheslotonthetipguard.Thearrowonthe
tiphandleshouldbepointingintheforwarddirectionforspraying.
Removing the Seal and Tip seal
1. Removethetipandtipguardfromthespraygun.
2. Removethesealandtipsealfromthebackofthetipguard.
Identifying Tip Sizes
Toidentifytipsizes,usethefollowingformula.A“517”tipsizewillbe
usedinthisexample.
Therstdigitmultipliedbytworepresentsthesizeofthespraypattern
whenspraying12”awayfromtheworksurface:
5x2=10”spraypattern
Thesecondtwodigitsrepresentthediameteroftheoriceonthetip:
17=.017”orice
NOTE: Worn spray tips will adversely affect the spray pattern
and result in reduced production, poor nish, and
wasted material. Replace worn tips immediately.
Cleanup
Maintainingacleangunisimportanttoensuretrouble-freeoperation.
Flushthegunaftereachuseandstoreinadrylocation.Donotleavethe
gunoranyofitspartsinwaterorsolvents.
Special cleanup instructions for use with flammable
solvents:
• Always ush spray gun preferably outside and at least one
hose length from spray pump.
• If collecting ushed solvents in a one gallon metal container,
place it into an empty ve gallon container, then ush
solvents.
• Area must be free of ammable vapors.
• Follow all cleanup instructions.
IMPORTANT: The sprayer, hose, and gun should be cleaned
thoroughly after daily use. Failure to do so permits material to cake,
seriously affecting the performance of the unit.
Always spray at minimum pressure
with the tip and tip guard removed
when using mineral spirits or any
other solvent to clean the sprayer,
hose, or gun. Static electricity buildup
may result in a fire or explosion in the
presence of flammable vapors. Hold
the gun firmly against a metal container while flushing.