Filter
Top Products
60 EN
Master Page: Left
Select Scenes
6 Press PLAY (U) and then press R.A.EDIT ON/OFF
on the remote control.
The Random Assemble
Editing Menu appears.
7 If using a Wipe/Fader at
the beginning of the
scene, press FADE/WIPE
on the remote control.
● Cycle through the
effects by pressing
repeatedly, and stop
when the one you want is displayed.
● You cannot use a Picture Wipe/Dissolve at the
beginning of Program 1.
8 At the beginning of the scene, press EDIT IN/
OUT on the remote control. The Edit-In position
appears in the Random Assemble Editing Menu.
9 At the end of the scene, press EDIT IN/OUT. The
Edit-Out position appears in the Random
Assemble Editing Menu.
10 If using a Wipe/Fader at the end of the scene,
press FADE/WIPE.
● Cycle through the effects by pressing
repeatedly, and stop when the one you want is
displayed.
● If you select a Wipe/Fader effect for an Edit-Out
point, the effect is automatically applied to the
following Edit-In point.
● You cannot use a Picture Wipe/Dissolve at the
end of the last scene.
● When you use Fader/Wipe effects, that time is
included in the total time (this does not apply
to Picture Wipe/Dissolve).
11 If using Playback Special Effects, press EFFECT.
(੬ pg. 56)
12 Repeat steps 8 through 11 to register
additional scenes.
● To change previously registered points, press
CANCEL on the remote control. The registered
points disappear, one at a time, from the most
recently registered point.
● If you are not using Wipe/Fader or Program AE
with special effects, repeat steps 8 and 9 only.
NOTES:
● When choosing a scene, set Edit-In and Edit-Out
points so that there is a relatively large difference
between them.
● If the search time for an in-point exceeds
5 minutes, the recording deck’s Record-Standby
mode will be cancelled and editing will not take
place.
● If there are blank portions before or after the Edit-
In and Edit-Out points, a blue screen may be
included in the edited version.
● Since time codes register time only as accurately
as seconds, the time code total time may not
match the total program time exactly.
● Turning off the camcorder’s power erases all
registered Edit-In and Edit-Out points.
● If you select Sepia or Monotone mode from
Program AE with special effects, you cannot use
the Dissolve or Black & White Fader. In this case
the Dissolve or Black & White indicator begins
blinking. Once the next Edit-In point is registered,
the effect is turned off. To combine these effects,
use Sepia or Monotone during recording, then use
the Dissolve or Black & White Fader during
Random Assemble Editing.
● It is not possible to use Wipe/Fader effects and
Program AE with special effects during Random
Assemble Editing using a DV cable.
Picture Wipe And Dissolve Menu
(available only for Random Assemble Editing)
You can use not only the wipe/fader effects on
page 32 but also the picture wipe and dissolve
effects below.
DISSOLVE: The new scene gradually appears
as the old one gradually disappears.
WIPE–CORNER: The new scene wipes in
over the previous one from the upper right corner to
the lower left corner.
WIPE–WINDOW: The next scene gradually
wipes in from the centre of the screen toward the
corners, covering the previous scene.
WIPE – SLIDE: The next scene gradually wipes
in over the previous one from right to left.
WIPE – DOOR: The previous scene wipes out
from the centre to the right and left, like a door
being pushed open to reveal the next scene.
WIPE–SCROLL: The new scene wipes in over
the last one from the bottom of the screen to the top.
WIPE – SHUTTER: The new scene wipes in
over the previous one from the centre toward the top
and bottom of the screen.
Automatic Editing To VCR
13 Rewind the tape in the camcorder to the
beginning of the scene you want to edit and press
PAUSE (9).
14 Press VCR REC STBY (79), or manually
engage the VCR’s Record-Pause mode.
15 Press the Recording Start/Stop Button on the
camcorder. Editing proceeds as programmed,
right through to the end of the last registered
scene.
PLAY
CANCEL
R.A.EDIT
ON/OFF
FADE/WIPE
EFFECT
EDIT IN/OUT
VCR REC STBY
PAUSE
1
2
3
4
5
6
7
8
––:–– ~
~
~
~
~
~
~
~
–
–
:
––
0
:
000
––
TOTAL
CODETIME
NIOUT
MODE
Selected parameter
USING THE REMOTE CONTROL UNIT (cont.)
GR-DV700PAL.book Page 60 Friday, February 21, 2003 4:04 PM