Filter
Top Products
27
• Avoid using strong cleaning agents such as benzine or alcohol.
• Cleaning should be done only after the battery pack has been
removed or other power units have been disconnected.
• Mold may form if the lens is left dirty.
• When using a cleaner or chemically treated cloth, refer to the
cautions that came with it.
• When removing the eyepiece, be sure to hold the viewfinder
securely.
Serious malfunctioning
If malfunctioning occurs, stop using the unit immediately and
consult your local JVC dealer.
LCD Monitor (for applicable models)
1. To prevent damage to the LCD monitor,
DO NOT . . .
.... push it strongly or apply any shocks.
.... place the camcorder with the LCD monitor on the bottom.
2. To prolong service life . . .
.... avoid rubbing it with coarse cloth.
3. Be aware of the following phenomena for LCD monitor use.
These are not malfunctions:
• While using the camcorder, the surface around the LCD monitor
and/or the back of the LCD monitor may heat up.
• If you leave power on for a long time, the surface around the LCD
monitor becomes hot.
How To Handle a CD-ROM (for applicable
models)
• Take care not to soil or scratch the mirror surface (opposite to the
printed surface). Do not write anything or put a sticker on either
the front or back surface. If the CD-ROM gets dirty, gently wipe it
with a soft cloth outward from the center hole using a circular
motion.
• Do not use conventional disc cleaners or cleaning spray.
• Do not bend the CD-ROM or touch its mirror surface.
• Do not store your CD-ROM in a dusty, hot or humid environment.
Keep it away from direct sunlight.
About moisture condensation . . .
• You may have observed that pouring a cold liquid into a glass
will cause drops of water to form on the glass’ outer surface.
This same phenomenon occurs on the head drum of a
camcorder when it is moved from a cool place to a warm
place, after heating a cold room, under extremely humid
conditions or in a place directly subjected to the cool air from
an air conditioner.
• Moisture on the head drum can cause severe damage to the
video tape, and can lead to internal damage to the camcorder
itself.
For Your Maintenance
1. After Use
Set the Power Switch to “OFF” to turn off the camcorder.
Open the LCD monitor* to an angle of over 60 degrees. Slide
EJECT to open the cassette holder, then remove the
cassette.
Close and lock the cassette holder by pressing the Close
button.
Close and lock the LCD monitor*.
Slide BATTERY RELEASE to remove the battery pack.
Attach the provided lens cap to the camcorder’s lens.
2. Cleaning The Camcorder
Wipe gently the exterior with a soft cloth. Put cloth in diluted
mild soap and wring it well to wipe off heavy dirt, then wipe
again with a dry cloth.
Open the LCD monitor* and wipe it gently with a soft cloth.
Be careful not to damage the monitor. Close the LCD
monitor*.
Blow the lens with a blower brush, then wipe it gently with
lens cleaning paper.
Turn the eyepiece counterclockwise and pull it out.
Remove dust from the viewfinder using a blower brush.
Re-attach the eyepiece and turn it clockwise.
* Applicable models only.
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
For GR-SXM740/SXM340U Owners:
Declaration of Conformity
Model Number : GR-SXM740/SXM340U
Trade Name : JVC
Responsible party : JVC AMERICAS CORP.
Address : 1700 Valley Road Wayne, N. J.
07470
Telephone Number : 973-317–5000
This device complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
This device complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
Change or modifications not approved by the party responsible
for compliance could void the user’s authority to operate the
equipment. This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
GR-SXM740U_EN 24/03/1905, 9:22 PM27