Kodak 5201 Film Camera User Manual


  Open as PDF
of 4
 
SENSITOMETRIC CURVES ➤
"0" on the x-axis represents normal exposure
of an 18-percent gray card in the red, green,
and blue layers of this film. A white card is
2 1/3 stops higher than normal exposure,
and there are at least 2 1/2 stops above that
for capturing specular highlight detail.
A 3-percent black card is 2 2/3 stops below
normal exposure. There are at least 2 1/2
stops of latitude below that for capturing
shadow detail.
MODULATION-TRANSFER CURVES ➤
This graph shows a measure of the visual
sharpness of this film. The x-axis, “Spatial
Frequency,” refers to the number of sine waves
per millimetre that can be resolved. The y-axis,
“Response,” corresponds to film sharpness. The
longer and flatter the line, the more sine waves
per millimetre that can be resolved with a high
degree of sharpness—and the sharper the film.
DIFFUSE RMS GRANULARITY CURVES ➤
To find the rms granularity value for a given
density, find the density on the left vertical scale
and follow horizontally to the sensitometric
curve and then go vertically (up or down) to the
granularity curve. At that point, follow
horizontally to the Granularity Sigma D scale
on the right. Read the number and multiply
by 1000 for the rms value.
SPECTRAL-SENSITIVITY CURVES ➤
These curves depict the sensitivity of this film to
the spectrum of light. They are useful for
determining, modifying, and optimizing
exposure for blue- and green-screen
visual effects work.
Spectral Sensitivity Curve Key
Spectral Dye Density Curve Key
Sensitivity of the yellow dye
forming layer
Sensitivity of the magenta dye
forming layer
Sensitivity of the cyan dye
forming layer
Midscale Neutral
Cyan Dye
Magenta Dye
Yellow Dye
Minimum Density
RECIPROCITY
No filter corrections or exposure
adjustments for exposure times from
1/1000 of a second to 1 second. In the
10-second range, increase exposure
1/3 stop and use a KODAK WRATTEN
Gelatin Filter CC10R.
I
DENTIFICATION
After processing, the Kodak internal
product code symbol (EK), product code
numbers 5201 (35 mm and 65 mm) or
7201 (16 mm), emulsion and roll number
identification, and EASTMAN KEYKODE
Numbers are visible along the length of
the film.
G
RAIN
The perception of graininess of any film
depends on scene content, complexity,
color, and density. In KODAK VISION2 50D
Color Negative Film 5201 / 7201, the
measured granularity is exceptionally
low.
S
HARPNESS
The perceived sharpness of any film
depends on various components of the
motion picture production system.
Camera and projector lenses, film printers,
and other factors play a role, but the
specific sharpness of a film can be
measured and charted in the Modulation
Transfer Curve.
Note: Sensitometric and Diffuse RMS Granularity curves are produced on different equipment.
A slight variation in curve shape may be noticed.
Camera Stops
-10.0
0.0
-6.0 -2.0 2.0 6.0
DENSITY
1.0
2.0
3.0
-8.0
-4.0 0.0 4.0
-2.9 -0.7
-3.7 -1.7 0.1
LOG EXPOSURE (lux-seconds)
0.0
DENSITY
1.0
2.0
3.0
RELATIVE LOG EXPOSURE
1.00.0 2.0 4.0
3.0
0.001
0.003
0.004
0.01
0.03
0.10
Granularity SIGMA D
RESPONSE (%)
10
1
100
1000
SPATIAL FREQUENCY (cycles/mm)
10
1
100
1000
LOG SENSITIVITY
0.0
*
1.0
2.0
4.0
700 750650600550500450400350300250
*Sensitivity = reciprocal of exposure (erg/cm ) required
to produce specified density
WAVELENGTH (nm)
2
3.0
1.8
1.0
1.4
0.2
0.6
DIFFUSE SPECTRAL DENSITY
-0.02
WAVELENGTH (nm)
800700300 400
750350 450 550 650
600
500
SPECTRAL DYE-DENSITY CURVES ➤
These curves depict the spectral absorptions of
the dyes formed when the film is processed.
They are useful for adjusting or optimizing any
device that scans or prints the film.
NOTE: Cyan, Magenta, and Yellow Dye
Curves are peak-normalized.
 previous