Metz 081 Camcorder User Manual


 
Press this key on the remote
control
The screen displays Explanation
20
Sat-Prog date VPS
enter date 11.12 14:20
696+S09A-GB
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
- -
SAT Timer recording
.
.
.
.
.
.
.
.
.
.
Time of day
?
MENU
return Help
TV
TV picture
Sat-Prog date VPS
enter date 11.12 14:20
696+S09B-GB
ARD
20:15
:
:
:
:
:
:
:
:
:
22:10
:
:
:
:
:
:
:
:
:
1
SAT Timer recording
12.12
.
.
.
.
.
.
.
.
.
Time of day
yes
?
MENU
return Help
TV
TV picture
AV
Sat-Prog date VPS
enter date 11.12 14:20
696+S09C-GB
ARD
20:15
:
:
:
:
:
:
:
:
:
22:10
:
:
:
:
:
:
:
:
:
1
- -
SAT Timer recording
12.12
.
.
.
.
.
.
.
.
.
Time of day
yes
?
MENU
return Help
TV
TV picture
AV
1. Call the menu „SAT timer
recording“
2. Enter the data for the pro-
gram to be recorded (see
example)
3. Store the programmed data
and return to the TV picture
or to standby mode
If no timer recordings have been programmed pre-
viously, this table is empty. Any previously program-
med settings will be displayed.
The timer menu requires the time of day and the date.
The time of day is taken from Megatext and the date
from the VPS signal. Note that some stations do not
transmit Megatext and/or VPS signals.
If there is no station with VPS and/or
Megatext stored in program position 01,
the time and/or date cannot be set auto-
matically and must be entered manually.
Two digits must be entered for each position of the
time and date, e.g. 01.09 for September 1st and 09:00
for 9 AM.
If you make a mistake while entering the data, the entry
in the current column or the entire line can be cleared
with the key. The entire line can be cleared only if
the key symbols in the top line are displayed in color.
-/--
If the TV set is not receiving a VPS signal when you are
programming it, a VPS signal can be set manually with
the key. If you have programmed a timer with VPS
and switched the TV set to standby mode, a TV set
with 7-segment display will display „SCAn“ about
one hour before the programmed start time to indicate
that it is scanning for the VPS start signal.
AV
The same data for the time of day and date must
be programmed into the video recorder on the AV
program position or on a program position on
which the video recorder does not receive a TV
station. An MVS system (optional extra) does this
automatically.
If desired, the timer recording can be terminated
at any time as described in section 8, step 3.
9. Timer-controlled Recording of SAT Programs
The menu SAT timer recording should be used only if you want to record a SAT program on a video recorder which does not have its own
SAT receiver. With this menu, a SAT signal from the TV set can be made available to a simple video recorder without its own SAT receiver.
Eight SAT timers can be preset up to two months in advance.
The settings for a TV set with 3 sockets is described in Section 7.1 or 8.2, „Timer recording“ of the Operating Instructions for the TV set.
Example: On 12.12.95, you want to record a film being transmitted from 20:15 to 22:10 by the SAT station on program position 1.
MENU
AV
0
1 2 3
4 5 6
7 8 9
OK
TV
or
If the childlock is active, you cannot
execute a SAT timer recording.
On TV sets with
1 EURO socket
50 Hz 50 Hz 50 Hz 50 Hz 50 Hz 50 Hz 50 Hz 50 Hz 50 Hz 50 Hz 50 Hz