Panasonic NV-GS4B Camcorder User Manual


 
49
ª
Condensation
If the Condensation Indication flashes after the Movie
Camera is turned on, condensation has formed inside the
Movie Camera. In this case, the Movie Camera power is
turned off automatically after about 1 minute.
Follow the steps below:
1
Take out the Cassette.
None of the other functions operate. Depending on the
amount of condensation, removing the Cassette may
even become difficult. If this happens, wait for
2 to 3 hours before taking the Cassette out.
2
Open the Cassette Compartment Cover and
wait for 2 to 3 hours.
The number of hours to wait depends on the amount of
condensation and ambient temperature.
3
2 to 3 hours later, turn on the Movie Camera
power and check to see if the Condensation
Indication is displayed.
Even if the Condensation Indication is not displayed,
as a precaution, please wait for another hour before
using the Movie Camera.
Watch for Condensation even before the Condensation
Indication is displayed.
Because condensation takes place gradually, the
Condensation Indication may not be displayed during the
first 10 to 15 minutes of condensation formation inside the
Movie Camera.
In extremely cold places, condensation may freeze and
form frost. In this case, the frost melts first, thus forming
condensation, and then it takes another 2 to 3 hours to
eliminate the condensation.
When the Lens is Fogged:
Set the [OFF/ON/MODE] Switch to [OFF] and leave the
Movie Camera in this condition for about 1 hour. When the
lens temperature becomes close to the ambient
temperature, the fog disappears naturally.
ª
Video Head Clogging and Care
If the heads (the parts that make contact with tape) are dirty,
mosaic-pattern noise may appear on the playback image, or
the screen as a whole becomes black. If the heads are
extremely dirty, recording performance deteriorates, and, in
the worst case, the Movie Camera cannot record at all.
Causes of Dirty Heads
Large quantity of dust in the air
High-temperature and high-humidity environment
Damaged tape
Long operating hours
Using Mini-DV Format Digital Video Head Cleaner
1
Insert the Head Cleaner into the Movie Camera
in the same manner as a Video Cassette.
2
Press the [
1
] Button, and approximately
20 seconds later, press the [
] Button. (Do not
rewind the tape.)
3
Take out the Head Cleaner. Insert a Video
Cassette and start recording. Then, play the
tape back to check the recorded image.
4
If the image is not still clear, repeat Steps1 to
3. (Do not use the Head Cleaner for 3 times or
more consecutively.)
Notes:
Do not rewind every time you use the Head Cleaner.
Rewind only when the tape reaches the end, and then use
it again from the beginning in the same manner as before.
If the heads become dirty soon after cleaning, the tape may
be damaged. In this case, immediately stop using that
Cassette.
Do not clean the heads excessively. (Excessive cleaning
may cause excessive wear of the heads. If the heads are
worn, images cannot be played back even after the heads
are cleaned.)
If the dirty heads css.4(ape )bes clh t.4(ape )-15.2(t).4(ape ).2(he4(ape )Cc)-11(l)h.4(are )]TJ0 -1.2576 TD80.0011 Tc40.0008 str cavie C[(be dab)-15.78(ra neehe head3f)-5.71a-11.6(ive )-15.2-11atw[(No2.2serv15.2(m)ices)entw[(No)-0.[(No2(eads )]TJTD0.0039 Tc-0.0093P15.15.c)11ul(Do not)-5.8( ) deal Cle.5())]TJ/TT1 1 Tf-0.7121 -1.2727 TD0 Tc0 Tw<0070>Tj/F11 1 Tf0.7121 0 T370.0042 Tc0.00932(he Head C.2(xces)-11.2( (C)n-11.6(ive )purct)8.8( )-s-11I)8.9( )13(r)-11.2( (a-she sam)-11.4a)-vices