Filter
Top Products
Connection to Monitor
•
As a connecting method varies according to instruments, refer to the manual supplied with
the instrument.
•Connect the cable after power is turned off.
•Set the 75Ω/ Hi-Z selection switch. If it is a intermediate device, switch it to Hi-z and if
it is final device, switch it to 75Ω. (Please refer to the Monitor Manual.)
DOME Camera
MonitorIntermediate
BNC
Connection to Power
•
Connect the adapter to the power input connector as shown in the figure below. Use a
DC12V 500mA. (The Adapter is not provided with the Dome Camera.)
DOME Camera
Adapter (not provided)
Power Input Connector
TROBLESHOOTING
SPECIFICATION
DECLARATION OF CONFORMITY
• When installing the camera on a ceiling or a wall, not to disturb adjustment of Tilt Base angle fix
the BNC-Power Cable on the Pan Base clip.
Notes
•After loosening Pan or Tilt Base holding screws, adjust its angle. And then tighten screws again.
•In case of adjusting the tilting, do not take the lens for preventing hysical shocks. Please take the Tilt Base.
• This dome camera is to be installed on the ceiling by factory default. In case of using camera on the wall,
readjust the Tilt angle as page 8 (Notes).
Notes
Panning & Tilting Control
You can adjust the Panning and Tilting angle freely. (Panning angle: 360°,
Tilting angle: 20˚~90˚)
1)
Adjustment Panning angle: After attaching the dome camera to a ceiling or a wall, adjust the
panning angle for better monitoring area by rotating the Pan Base. The panning angle can be
adjusted 360˚ freely.
2) Adjustment Tilting angle: After attaching the dome camera to a ceiling or a wall, adjust
the tilting angle for better monitoring area by rotating the Tilt Base. The tilting angle can
be adjusted to 20˚ from 90˚ freely. (based the ceiling surface)
Resistance of copper wire [at 20C˚ (68˚F)]
• As the voltage drop according to the length of the cable in the above table, a camera may
malfunction if there is an excessively long cable run.
* Voltage for camera operation: 12V DC ±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
For DC Power Type
Copper wire size (AWG)
#24(0.22mm
2
) #22(0.33mm
2
) #20(0.52mm
2
) #18(0.83mm
2
)
Resistance ( Ω/ m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
MINI DOME CAMERA USER’S MANUAL
11
MINI DOME CAMERA USER’S MANUAL
10
MINI DOME CAMERA USER’S MANUAL
14
MINI DOME CAMERA USER’S MANUAL
13
<Installing the camera on a ceiling> <Installing the camera on a wall>
MINI DOME CAMERA USER’S MANUAL
9
MINI DOME CAMERA USER’S MANUAL
12
INSTALLATION
Accessories
Installing Camera
User Manual Quick Install Guide
Cable Rubber
Template
M4 Taping Screw 2EA
1. Fix the camera to a ceiling or a wall using two screws.
2. After fixing it, adjust its pan base and
tilt base properly.
3. After adjusting them, secure the shield
case and dome-cover.
The SID-50 includes the following built in functions
MINI DOME CAMERA USER’S MANUAL
8
CAMERA OPERATION
DIMENSION
Screw
Shield Case
Dome Cover
Hole
BNC-Power Cable
Pan Base
You can rotate the lens
from 360˚
Tilt Base Holding
Screws
Tilt Base
You can adjust up and down
the camera (20˚~90˚).
Pan Base Holding Screw
Auto Functions
Electronic Shutter
Speed
WHITE BALANCE
BACKLIGHT
GAIN CONTROL
SSNR
(Noise Reduction)
SENS UP
SHARPNESS
Setting Value
ESC
ATW
MIDDLE
MIDDLE
LOW
ON
ON
Descriptions
The speed is controlled according to the
brightness of the screen.
It can be used within the color temperature
range 1,800K~10,500K(Ex fluorescent light,
outdoor, sodium vapor lamp or inside tunnels)
The gain increases within the range of
6dB~34dB
The gain increases or decreases within the
range of 6dB~34dB
There is sufficient reduction in noise levels
without causing much ghost imaging
It helps maintain a bright, clear screen image by
automatically detecting changes in the level in
low light levels without causing much ghost
imaging.
The outline of the video image becomes cleaner
and more distinctive as the level of
SHARPNESS increases.
Application of Council Directive(s) 89 / 336 / EEC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment MINI DOME CAMERA
Model Name SID-50
Beginning Serial NO. S6300001
Year of Manufacture 2006. 03. 01
Conformance to EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD
Legal Representative in Europe
Signature Signature
Full Name YOUNG TAEK SON Full Name
Position QUALITY CONTROL MANAGER Position
Place CHANGWON, KOREA Place
Date 2006. 03. 01 Date
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details
of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not
be mixed with other commercial wastes for disposal.
SID-50N SID-50P
ITEM
Power Source
Total Pixels
Effective Pixels
SIZE
Scanning System
Synchronization
Frequency
LENS(Built-in)
Resolution
Video Output
S/N(Y signal)
Min.Illumination
Auto Functions
Monitoring Pan
Angle Tilt
Operating temperature/Humidity
Dimention
Weight
DC 12V±10%/Max. 1.8W
811(H) x 508(V) 795(H) x 596(V)
768(H) x 494(V) 752(H) x 582(V)
1/3 inch Super HAD CCD
2:1 Interlace
Internal Only
Horizontal:15.734 KHz/Vertical :59.94 Hz Horizontal: 15.625 KHz/Vertical : 50Hz
Built-in Fixed Lens 120 f=3.0mm, F2.0
540 TV Lines(Min.)
CVBS : 1.0Vp-p/75
50 dB (AGC Off,Weight ON)
0.05Lux/F1.2(Sens-up), 0.3Lux/F1.2
Electronic shutter speed AUTO
WHITE BALANCE AUTO
BACKLIGHT AUTO
Gain Control AUTO
SENS-UP AUTO
SSNR(Noise Control) AUTO
SHARPNESS AUTO
Manual 360
Manual 20 ~ 90
-10˚C to +50˚C / 30% to 80% RH
99.2mm(W) x 99.2mm(H) x 67mm(D)
200g
CCD
Sync.
E
L
E
C
T
R
I
C
A
L
Pan Base clip
99.2
2-Ø 4.2
63.5
99.2
99.2
R 41.2
67
If you have trouble operating your camera, refer to the following. If the guidelines do not
enable you to solve the problem, contact an authorized technician.
The image on the screen is dim.
• Check if the lens are stained. If dirty, clean the lens with soft, clean cloth.
• The image is dimmer at night than daytime. If the focus is not right, adjust it at daytime
.
The contrast on the screen is too weak.
• Adjust the contrast feature of the monitor.
• If the camera is exposed under too strong light, change the camera position.
• Adjust the lens BACK FOCUS again.
The camera is not work properly, and the surface of the camera case is hot.
• Check that you have connected the camera to a proper power (DC12V ).