Filter
Top Products
102
Setting the Status Display on the Viewfinder Screen and the LCD Monitor
Chapter 5 Menu Displays and Detailed Settings
2 Turn the MENU knob until x moves to the
character position that you want to select, then
press the MENU knob.
4
Repeat step 3 for each of the remaining characters.
5
When the input is complete, turn the MENU knob to
move x over END, then press the MENU knob.
This ends the input, and returns to the SHOT ID page.
To insert a space
In step 3 above, move x over INS, and press the MENU
knob. To cancel inserting a space, move x to RET, and
press the MENU knob.
To delete a character
In step 3 of “Setting the shot ID” on page 101, move x
over DEL, and press the MENU knob. This deletes the
character under x in the shot ID row.
To cancel deleting the character, move x over RET, and
press the MENU knob.
To cancel changing shot ID
Before executing step 5 of “Setting the shot ID” on page
101, move b to ESC, then press the MENU knob.
Displaying the status confirmation
windows
You can confirm the settings or status of the camcorder on
the screen by displaying the following two windows.
• CAMERA STATUS window
• VTR STATUS window
You can use the SET STATUS page of the OPERATION
menu to set whether or not the status confirmation
windows are displayed.
Display content of the window
CAMERA STATUS window
This window allows you to confirm the following items
related to the camera setting.
• FORMAT: Camera scan mode (when recording), or
tape format (when playing back)
- I: Interlace scan mode
- P: Progressive scan mode
- 24P 2.3: 24 frames per second, progressive scan mode
(converted to 60i at 2-3 pulldown)
- 24P 2.3.3.2: 24 frame per second, progressive scan
mode (converted to 60i at 2-3-3-2 pulldown)
(”PB” is displayed behind the item during playback.)
• ASSIGN: The setting of ASSIGN switch (1 to 4)
• FRONT AUDIO VOL: The setting of the AUDIO
LEVEL knob on the front of the camcorder
• ZEBRA: The setting of zebra
Information displayed below “Actual State” appears only
when a CBK-SD01 SDI Output Board is installed in the
DSR-450WS/450WSP.
• REAR BNC: Output signal of the VIDEO OUT
connector
VTR STATUS window
This window allows you to confirm the following items
related to VTR.
Example: When entering the letter “+”
ID-1 :? +
ID-2 :
ssssssssssss
ID-3 :
ssssssssssss
ID-4 :
ssssssssssss
i#$%&'()*+,-./012345678
9:;<=>?@ABCDEFGHIJKLMNOP
QRSTUVWXYZ[ ]abcdefghijk
lmnopqrstuvwxyz~
ESC END
12 SHOT ID
TOP
ID-1 : CM 015
ID-2 :
ssssssssssss
ID-3 :
ssssssssssss
ID-4 :
ssssssssssss
$%&'()*+,-./0123456789:
;<=>?@ABCDEFGHIJKLMNOPQR
STUVWXYZ[\]_
INS DEL RET ESC END
12 SHOT ID
ID-1 : CM015
ID-2 :
ssssssssssss
ID-3 :
ssssssssssss
ID-4 :
ssssssssssss
$%&'()*+,-./0123456789:
;<=>?@ABCDEFGHIJKLMNOPQR
STUVWXYZ[\]_
INS DEL RET ESC END
TOP
12 SHOT ID
TOP
Move x over INS.
Space inserted.
CAMERA STATUS
FORMAT : I
ASSIGN <1> ATW <2> OFF
<3> OFF <4> OFF
FRONT AUDIO VOL : ENABL
ZEBRA: OFF SELECT: 1
DET : 70% APT : 10%
DET2: 100%
- Actual State ---------
REAR BNC :VBS
VTR STATUS
16bit DF F.MIC:MONO
REC FORMAT : DVCAM
AUDIO MODE : FS32K
DF/NDF : DF
INTERVAL REC : OFF
REC TIME : 0.5S
INTERVAL TIME : 30S
VTR TRIGGER MODE : ----
STANDBY OFF TIMER: 1MIN