Filter
Top Products
The Camera features an omni-directional antenna which is most effective when used in the
UPRIGHT position.
1)
2)
How to lock out un-used channels on the 4 channel receiver.
Connect both the Camera and the Receiver to their respective power adaptors.
*IMPORTANT: The camera requires an 8- 9V power supply, the receiver uses a 12V power
supply.*
Connect the Receiver to the equipment you wish to view the camera on (monitor, AV TV, VCR,
DVR etc) using the supplied RCA-RCA cable and then turn the receiver ON via the switch on the
left.
Direct the antenna of the receiver toward the antenna of the Camera. The antenna can be
swivelled to face in the appropriate direction to a maximum of 180° (90° either side of centre).
Once the antenna is correctly positioned, check the image for clarity and make minor adjustments
to obtain the best picture. obtain the best picture
Using the remote control:
1) Press the button to lock the receiver to one specific channel
To cycle through specific channels, press the button (”L” should display on the front of the
receiver) followed by the channel number/s and the button again.
2)
3)
4)
In some cases to you will also need to adjust the
position of the Camera and Receiver to suit your particular situation. Try slightly different locations
for either unit to achieve optimal results.
If you are mounting the camera to a ceiling or eave, unscrew the camera stand from the camera
body and carefully screw it into position on the top side of the camera using the two holes that are
provided or the picture will appear on your screen upside down.
Camera with Stand
Small Plug Power Adaptor (8V)
Large Plug
Power Adaptor
(12V)
VideoOut
To Video &
Audio IN
MonitororTV
Left&Right
AudioOut
DC12V
Socket
A/VCable
ChannelSelector
Button
Active
Channel
Display
Poor Picture:
Lines only - no clear picture:
Picture ghosting or interference:
No picture:
Realign antennas until image quality improves, slightly adjust the position of the Night Hawk Camera
or Receiver. Change the location of the Camera, or use a different Camera in the location experiencing interference
that is on a different channel. In some cases interference may be caused by another device on a similar frequency to
the channel you are using. Change to one of the other channels and check the signal quality again.
Check to confirm there is no microwave oven or other 2.4GHz equipment
operating close by ie; Cordless Telephones, Wireless Baby Monitors, Wireless LAN equipment etc. Make sure the
Receiver is on the correct channel for the particular camera.
Some home appliances such as Wireless LANs, 2.4GHz portable telephones
and Microwave ovens operate on or near the 2.4GHz frequency. If you receive interference from such an appliance,
try moving the Camera or Receiver to location further away from the appliance or in the event of interference from a
Wireless LAN device, try changing the Wireless LAN to a different channel to improve the signal quality.
check the receiver to confirm it is turned ON and make sure the A/V connection of the Receiver is not
plugged into the Audio Out socket. Make sure the Receiver is on the correct channel. Check that the channel on the
receiver is the set to the same as the camera you wish to view. Check to ensure the camera is plugged in and has
power (cup your hands around the camera and you should see a faint red glow from the IR LEDs). You can use the
infrared lighting facility to pick up a picture inside a dark environment. If your monitor does not display a picture in a
dark environment, check the camera to be certain that infrared lighting is within range of the subject. Try to move the
item within the 2-3m (6-9ft) range of the Cameras IR LEDs or place the Camera nearer to the object until a clear
picture is displayed on the Monitor.
FCC Notice
CE Notice
We, Swann Communications of 10612 Shoemaker Avenue, Bldg A, Santa Fe Springs, CA 90670 USA,
declare under our sole responsibility that the product:
This product meets the requirements specified in Part 15 of FCC Regulation. Operation rests with the
following two conditions:
(1) The equipment should not cause any harmful interference;
(2) The equipment must receive and process any interference, including any possible interference
caused by operation mistakes. After testing the product, we confirm that it complies with the provision for
class C digital equipment in the 15th part in FCC regulation; and the receiver complies with the
limitations for class B digital equipment in Part 15 of FCC regulation. The product generates, applies and
emits radio waves. It might cause harmful interferences to wireless communication if not be installed and
used following the description of the manual. The product may cause interference in residential area, and
the customer should take remedies to eliminate the interference at their own costs. If the product causes
any harmful interference to wireless equipment or disturbs the receiving of TV signals (it can be identified
by turning on and off the product), you can solve the trouble by following methods:
(1) Re-adjust the product or put it in another place;
(2) Extend the distance between the equipment interfered and the product; and
(3) Refer to dealers or experienced radio electrician for help.
SW-P-WOC2
This product complies with standards including ow oltage evice Directive 73/23/EEC;
Directive 89/336/EEC and Directive 1999/5/EC. It passed the subject tests by the authority
concerned and is authorized to bear mark.
LV D EMC
R&TTE
CE
6
3
Troubleshooting, Hints and Tips
Setting Up Your System
ON/OFF
Switch