ENGLISH
24
8 7.1 CH INPUT LEVEL
This sub-menu is to adjust the speaker levels for
7.1-channel input sources.
Here you will adjust the volume for each channel so
that they are all heard by the listener at the same
level.
1.
Select “7.1CH INPUT” in the SETUP MAIN
MENU with the
or cursor buttons, and
press the ENTER button.
2.
To select “VIDEO IN”, press or cursor
button.
3.
Using the or cursor buttons, select the
video input source which is emitted from
Monitor out in the 7.1 CH INPUT function.
The input source is switched by pressing the
or cursor buttons as follows;
LAST ↔ TV ↔ DVD ↔ VCR1 ↔ DSS ↔
AUX1 ↔ V-OFF ↔ LAST ↔
Notes:
•
When select LAST, the source is set previous
source before 7.1 CH INPUT function
is activated.
•
When select V-OFF, no signal is emitted from
monitor out terminal.
4.
To Select desired channel , press the or
cursor buttons.
5.
Using the or cursor buttons, adjust the
volume level of each channel.
6.
After you complete this portion of the set up,
move the cursor to “MAIN” with the
or
cursor buttons and press the ENTER button.
Notes:
•
These settings will be memorized to 7.1CH INPUT
source.
• This feature can be directly selected with the
CH.SEL button of the remote controller.
87.1CHINPUTLEVEL
VIDEO IN : LAST
FRONT L : 0 dB
CENTER : 0 dB
FRONT R : 0 dB
SURR.R : 0 dB
SURR.B R : 0 dB
SURR.B L : 0 dB
SURR. L : 0 dB
SUB W : 0 dB
MA I N EX I T
LEVEL (VOLUME LEVEL):
Adjust the Multi-speaker output level with or
cursor button.
Note:
• This setting can be changed when the Surr Back is
set “NONE” in 2-1 SPEAKER SIZE menu.
When this setting is unavailable, “✽✽✽” is
displayed
MAIN ROOM STATUS:
Selected input source in the main room will be
displayed.
Note:
• If “VOLUME” is set to “FIXED”, the multi-room
output level cannot be adjusted from the second
zone.
After you complete this portion of the set up, move
the cursor to “MAIN” with
or cursor buttons and
press ENTER button.
9 MULTI PLC SETUP
This submenu is for setting up the Multi PLC
feature of the ZR6001.
1.
Select “9. MULTI PLC” in the SETUP MAIN
MENU with the
or cursor buttons and
press the ENTER button.
2.
To select desired contents, press or
cursor button.
MULTI PLC SEVER:
Select “ON” or “OFF” with the / cursor buttons
to turn the Multi PLC Server feature ON/OFF.
CONNECTION MODE:
Select the Connection Mode of the Multi PLC
feature with the / cursor buttons.
The available Connection Modes are:
-AUTO :Normal mode
Use this mode as standard.
-HIGH AUDIO QUALITY(H-AQ)
:Emphasizes audio quality.
Use this mode to listen to high audio quality.
(However, when multiple ZC4001 units are
connected, audio may be lost or noise may
occur in a ZC4001 that experience poor
reception.)
-HIGH RELIABILITY(H-R)
:Emphasizes reliability.
Use this mode when multiple ZC4001 units are
connected, audio is lost, or noise occurs.
9MULTIPLC
MULT I
CONNECT I ON MODE :
AUTO
HIGH AUDIO QUAL I TY
HIGH RELIABILITY
GP
ID SETTING:START
MA I N EX I T
PLC SERVER:ON
GP-ID SETTING
To set a Group ID, connect the AC power cables of
the ZR6001 and ZC4001 to wall power outlets as
close to each other as possible.
Set the Group ID simultaneously for the ZR6001
and ZC4001.
<ZR6001>
Using the OSD menu system, set “GP-ID
SETTING” to “START”.
1.
Select “9. MULTI PLC” in the SETUP MAIN
MENU with the
or cursor buttons, and
press the ENTER button.
2.
Select “GP-ID SETTING” with the or
cursor buttons.
<ZC4001>
1.
Press and hold the ENTER button for 5 sec or
more.
9MULTIPLC
MULT I
CONNECT I ON MODE :
AUTO
HIGH AUDIO QUAL I TY
HIGH RELIABILITY
GP
ID SETTING:START
MA I N EX I T
PLC SERVER:ON
06.3.6, 4:28 PMPage 24
