© Titan Tool Inc. All rights reserved. 29
SAE O-Ring Fitting Installation
Steps 1 & 2:
Step 3:
Step 4:
Step 5:
Cautions:
Lubricate
Lubricate
Tighten nut
Recess
gap
No gap
Align
Hold
this part
stationay
Avoid screwing fitting in too far.
Avoid leaving fitting too far out.
Bent washer allows
for o-ring extrusion
O-ring cut on
thread
Accessories and Service Kits
These items may be purchased separately from your local
Speeflo distributor.
Part #
Description
930-005 Paint Filter Element, 5 Mesh
(for high viscosity materials)
930-006 Paint Filter Element, 50 Mesh
(for conventional materials)
930-007 Paint Filter Elements, 100 Mesh
(for low viscosity materials)
160-124 Nylon Paint Strainer - 1 Gallon (Pack of 24)
160-524 Nylon Paint Strainer - 5 Gallon (Pack of 24)
101-208 Grounding Clamp
101-212 Grounding Wire, 12 Gauge x 25'
700-925 Piston Lube
430-362 Coolflo™ Hydraulic Fluid, 1 Quart
430-361 Coolflo™ Hydraulic Fluid, 1 Gallon
930-050 Service Kit for Paint Filter
944-050 Service Kit for Bleed Valve
Athletic Field Marking Kit/Turf Kit
Item
Part # Description Quantity
1 424-821 Axle assembly ......................................1
2 570-010 Cotter key.............................................2
3 870-404 Hex nut.................................................2
4 424-213 Wheel assembly...................................2
Turf Kit Installation
1. To install the turf kit permanently:
a. Remove the lever assembly from the handle by removing
the screw and nut from the clamp that attaches the lever
assembly to the handle.
b. Disconnect the cable assembly form the lever actuator
assembly by removing the machine screw from the lever
actuator assembly.
c. Remove the cable locking nut located on the inside of the
gun bar bracket.
d. Slide the exposed cable through the slot in the gun bar
bracket and remove the entire cable assembly.
To install the turf kit temporarily:
a. Disconnect the nut and the socket head screw from the
the lever actuator assembly by removing the machine
screw from the lever actuator assembly.
b. Tie back the loose cable to the sprayer’s frame using
cable ties or t ape.
2. Remove the nut and the socket
head screw from the frame and
the lever actuator assembly. The
lever actuator will now hang from
the front wheel assembly by the
connecting ring.
3. With the sprayer tilted back,
remove the front wheel assembly
by removing the four nuts,
washers, and hex head screws
that secure it to the frame.
4. Bolt the turf kit assembly to the
frame using the four nuts,
washers, and hex head screws removed in the previous step.
Frame
Turf Kit
Assembly
1. Pull washer and o-
ring back as far as
possible.
2. Lubricate o-ring and
entrance port.
3. Screw fitting in until
washer pushes o-
ring into entrance
and sits flat against
port. (Do not
tighten! - only do this
step hand tight to
compress o-ring into
port!)
4. Back fitting out no
more than one
complete turn to
align as required.
5. Torque nut wrench
tight holding backup
on fitting. This
should expose a
recess gap behind
the nut which can
act as an indicator
that the fitting is
assembled correctly.
(This is a feature for
a specific version of
this fitting only -
which screws into
the cylinder head.
Other fittings, as the
ones which attach to
the hydraulic pump,
assemble the same
but may not have
the indicator.)
