Filter
Top Products
FOCUSING MODE
NOTE : Select the proper focus mode with the focus mode button (key # 16) and the main command knob on the housing. For more
detailed information concerning the operation of the different focus modes consult the Canon instruction book for the
Canon 1Ds Mk
III.
USING THE HOUSING
Whenever changing ports or O-rings, it is highly advisable to perform a simple seal test without the camera inside. Strapping a weight to
the housing and lowering the unit to a depth of 30 to 50 feet of water for at least 10 minutes will assure you that the seating of the new
port or o-ring is proper. This test, though time consuming and often considered unnecessary, may save your camera equipment from
irreparable water damage.The housing is now ready for the dive.
CAUTION: Never jump into the water with the housing. It is best to have the system handed to you after you have made your entry, or
have it lowered to you on a rope. Make certain that ropes of other equipment stay clear of the system.
When photographing, be sure to respect the environment. Avoid damaging marine life or manipulating sea creatures to obtain a pleasing
photo
. The housing is slightly negatively buoyant so that you can lay it down on the bottom, but avoid laying it on living coral or other
delicate marine life.
Changing the memory card
Always take care to thoroughly dry the housing before opening it to change memory card. Wipe the housing off with a dry towel. If
possible it is suggested that the housing be blown dried by directing an air nozzle around the main o-ring before opening.
Rest the housing on its front with the lens facing down, be carefull to protect the port surface, release the top latch rst then the two side
latches simultaneously. Lift the rear part of the housing and place it in a secure location.
This minimizes the possibility of any residual
water falling into the housing and on to the camera when the housing is opened or damage to the sealing surface
.
TRANSPORTING THE AQUATICA Pro Digital housing
Store the AQUATICA Pro Digital housing in a sturdy, shock proof container. When travelling by air, remove or loosen the port. This
allows for equalization of the air pressure inside the housing to the external air pressure. Failure to do so may cause serious damage
to the acrylic ports. Avoid travelling with the camera mounted in the housing. If you must do so, remove the lens as external impact or
shocks can damage the camera bayonet mount.
CARE AND MAINTENANCE
Of the housing:
After each and every salt water dive, your housing system should be soaked or rinsed in fresh water. The housing system should soak
in fresh water for at least 30 minutes. During this soaking period reach into the water and operate all the controls several times.
Be sure to remove the housing’s main o-ring and clean it after every use. Refer to Maintenance: Of the O-rings. To ensure that the hand
grips won’t fuse on to the housing due to the exposure to salt water, it is also a good practice to occasionally remove the hand grips.
Clean and lubricate the bolts with a small amount of WD-40.
WARNING: Use WD-40 carefully, sparingly and only on metal to metal surfaces. WD-40 can damage the acrylic on the ports, the
optical surfaces on lens as well as the O-rings.
Of the Ports:
Care should be taken with the Dome Port and Macro Port to avoid scratches on the lens surface. The acrylic port is softer than glass
so minor exterior scratches are often unavoidable. However, since the indices of refraction for acrylic and water are almost equal the
scratches will not seriously impair image quality. Internal scratches(air side) must be avoided as they do not ll in with water and will
affect the quality of the image.
Clean the dome using only products recommended for cleaning acrylic and a soft lint free cloth. Dust on the interior surfaces of the port
can be removed with a soft camel hair brush or a blower brush. Caution must be taken when using aerosol devices as not to spray the
lens material with the liquid propellant as this may seriously affect the optical properties of the port. Use of pressurize air from a dive
tank is not recommended, the force of the air stream may easily dislodge a port or O-ring, It is advisable that ports should be removed
and serviced after avery dive.
page 10