Filter
Top Products
8. Adjust the horizontal phase by pressing or . The adjustable range is 0-2.0 µs.
6-3. Line-lock Sync Mode (LL)
Note: The line-lock (LL) sync mode is not available when the camera operates on DC
power.
1. Move the cursor to the SYNC parameter and select LL.
Note: The settings in this menu can be made only when the multiplexed vertical drive
signal (VD2) is not supplied to the camera.
2. After confirming that the cursor is on
LL, press . The vertical phase
adjustment menu appears on the moni-
tor.
3. Supply the video output signal of the
camera to be adjusted and the refer-
ence camera video output signal to a
dual-trace oscilloscope.
4. Set the oscilloscope to the vertical rate
and expand the vertical sync portion on
the oscilloscope.
5. Move the cursor to COARSE.
6. Press or to match the vertical phase for both video output signals as closely as
possible. (COARSE adjustment can be incremented in 16 steps by 22.5 degrees by
pressing or .)
Note: After the sixteenth step, the adjustment returns to the first step.
7. Move the cursor to FINE.
8. Press or to match the vertical
phase for both video output signals as
closely as possible.
(FINE adjustment can be made up to
22.5 degrees by pressing or .)
Notes:
• When the “I” cursor reaches the “+” end, it jumps back to “–”. At the same time,
COARSE is incremented by one step to enable a continuous adjustment. The
reverse takes place when the “I” cursor reaches the “–” end.
• When or is kept pressed for a second or more, the “I” cursor moves faster.
• To reset COARSE and FINE to the values preset at the factory, press or
simultaneously. COARSE and FINE adjustments are preset at the factory to zero-
crossing of the AC line phase.
• If the AC line contains noise (spike noise, etc.), the stability of the vertical phase of
the camera video output signal may be disturbed.
7. White Balance Setting (WHITE BAL)
7-1. Auto-Tracing White Balance Mode (ATW)
You can select one of two modes for white balance adjustment as follows:
• ATW (Auto Tracing White Balance)
In this mode, the color temperature is monitored continuously and thereby white bal-
ance is set automatically. The color temperature range for the proper white balance is
approximately 2 600 - 6 000K. Proper white balance may not be obtained under the fol-
lowing conditions:
1. The color temperature is out of the 2 600 - 6 000K range.
2. When the scene contains mostly high color temperature objects, such as a blue
sky or sunset.
3. When the scene is dim.
In these cases, select the AWC mode.
Move the cursor to the WHITE BAL parameter and select ATW. The white balance of the
camera is automatically set.
• Automatic White Balance Control Mode (AWC)
In this mode, accurate white balance is obtained within a color temperature range of
approximately 2 300-10 000K.
1. Move the cursor to the WHITE BAL
parameter and select AWC → PUSH
SW.
2. Press to start the white balance
setup. The PUSH SW is highlighted to
indicate that the white balance is being
set.
3. When the white balance setting is com-
pleted, the PUSH SW returns to normal
display.
Note: In case that the white balance is not set, the PUSH SW Is being highlighted.
4. When you want to adjust the white bal-
ance manually, press to select
AWC and press . The AWC menu
appears on the monitor. (When ATW is
selected, pressing displays the
ATW menu.)
Fine Adjustment for AWC (ATW) Manually
You can add the detailed setting for white balance setting manually.
1. To set MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2
OFF and ELC mode”.
2. Move the cursor to R.
3. Press or to obtain the optimum amount of red gain.
4. Move the cursor to B.
5. Press or to obtain the optimum amount of blue gain.
Note: When you need to set MASK SET, re-adjust to obtain the optimum amount of red and
blue gain.
1 (1 - - 16): 0 degrees
2 (1 - - 16): 22.5 degrees
16 (1 - - 16): 337.5 degrees
** SYNC **
V PHASE
COARSE 1(1--16)
FINE I........
- +
RET END
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
SYNC INT
WHITE BAL AWC
→
PUSH SW
MOTION DET OFF
LENS DRIVE DC
END SET UP ENABLE
↵↵
** AWC **
R ....I....
- +
B ....I....
- +
MASK SET
RET END
↵