Filter
Top Products
C1300M-B (6/05) 9
Quick Start Guide – System Setup
Quick Programming Guide
Access the main menu (preset 95). See the Accessing
Main Menu (Preset 95) section.
Use the joystick to position the cursor beside
menu selection. If your controller does not have a
joystick, use the up or down key.
Press Iris Open; the submenu/cursor moves to the right.
Move the joystick up or down to view selections.
If your controller does not have a joystick, use the
up or down key.
Press Iris Open to make selection.
Press Iris Close to cancel selection.
Presets
The following presets are reserved for special functions.
Preset Function
33 Flip command (disabled)
86 Wiper
87 Washer
88 IR filter IN (color)
89 IR filter OUT (black-white)
90-91 Manual limit stops
92-93 Scan limit stops
95 Select main programming menu
96 Stop a scan
97 Random scanning
98 Frame scanning
99 Start auto scanning
NOTE: For American Dynamics controllers with only 32 presets, switch SW3-1
on the dome drive to the ON position. When SW3-1 is ON, preset
99 becomes 32 92 becomes 25
98 becomes 31 91 becomes 24
97 becomes 30 90 becomes 23
96 becomes 29 89 becomes 22
95 becomes 28 88 becomes 21
93 becomes 26
If the limit stops are turned off, presets 23-26 can be used as regular presets.
WIPER**
WIPER CONTROL
WIPER MODE
WIPER DWELL (SECS)
WIPER TIME (MIN)
<SET WASHER SEQUENCE>
BACK
EXIT
LYNE SYNC
LINE SYNC
LINE SYNC PHASE
BACK
EXIT
PATTERNS
PATTERN NUMBER
<PROGRAM PATTERN>
<CLEAR PATTERN>
BACK
EXIT
REFERENCE INFORMATION
PATTERN USAGE
REMAINING
ALARMS
RESUME
SEQUENCE (SECS)
RESET DELAY (SECS)
<ALARM SETTINGS>
BACK
EXIT
POWER UP
POWER UP ACTION
BACK
EXIT
ZONES
ZONE NUMBER
ZONE NOT DEFINED
<EDIT ZONE LABEL>
<EDIT ZONE>
ZONE ENABLED
ZONE BLANKING
<CLEAR ZONE>
BACK
EXIT
AUX
AUX 1 MODE
DWELL TIME (SECS)
AUX 2 MODE
DWELL TIME (SECS)
BACK
EXIT
CLEAR
CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL WINDOW BLANKING
RESTORE FACTORY DEFAULTS
BACK
EXIT
MOTION
PROPORTIONAL PAN
PARK TIME (MINUTES)
PARK ACTION
SCAN SPEED (DEG/S)
PRESET FREEZE FRAME
LIMIT STOPS
<SET MANUAL STOPS>
<CLEAR MANUAL STOPS>
<SET SCAN STOPS>
<CLEAR SCAN STOPS>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
BACK
EXIT
ADVANCED SETTINGS
SHUTTER SPEED
AGC LIMIT
AUTO IRIS
AUTO IRIS LEVEL
AUTO IRIS PEAK
AUTO SHARPNESS
SHARPNESS LEVEL
AUTO WHITE BALANCE
R GAIN
B GAIN
BACKLIGHT COMP
VIDEO LEVEL
WIDE DYNAMIC RANGE*
BACK
EXIT
SET WINDOWS
WINDOW NUMBER
<EDIT WINDOW LOCATION>
<EDIT WINDOW ZOOM>
ENABLE WINDOW
REVERSE
CLEAR WINDOW
BACK
EXIT
ALARM SETTINGS
ALARM NUMBER
ALARM PRIORITY
ALARM ACTION
ACTIVATE AUX
ALARM CONTACT
BACK
EXIT
UNIT SETTINGS
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERNS>
<ZONES>
<WINDOW BLANKING>
<ALARMS>
<WIPER>
<AUX>
<CLEAR>
<PASSWORD>
BACK
EXIT
ADDITIONAL
FREE MEMORY
LAST RESET
AZIMUTH ZERO OFFSET
MOTOR ACTIVE
CAMERA ACTIVE
FPGA VERSION
VIDEO LEVEL
CAMERA
<EAB>
<PMAB>
LANGUAGE 1
LANGUAGE 2
LANGUAGE 3
LANGUAGE 4
LANGUAGE 5
LANGUAGE 6
BACK
EXIT
SYSTEM INFORMATION
UNIT MODEL
POWER MODULE MEMORY
SOFTWARE VERSION
BIOS VERSION
FONT VERSION
COMM
D ADDRESS
P ADDRESS
CM9500 MODE
32 PRESET MODE
PROTOCOL
<ADDITIONAL>
BACK
EXIT
LABEL POSITION
[ZONE LABEL- - - - - - - -]
[PRESET LABEL- - - ---]
[ALARM 1- - - - - - -]
SAVE AND EXIT
CANCEL AND EXIT
HELP
XXX/-XXX
NE
XXX.XXX
DISPLAY SETUP
PRESET LABEL
ZONE LABEL
ZOOM
AZMUTH/ELEVATION
DIRECTION
ALARM MESSAGE
<LABEL POSITION>
RESTORE FACTORY DEFAULTS
BACK
EXIT
PELCO EXSITE IPSXM
LANGUAGE
UNIT INVERSION
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<UNIT SETTINGS>
<POSITION CALIBRATION>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
EXIT
POSITION CALIBRATION
PRESET NOT DEFINED
<EDIT PRESET SCENE>
<CLEAR CALIBRATION PRESET>
<RECAL USING CAL PRESET>
BACK
EXIT
REFERENCE INFORMATION
AZIMUTH
ELEVATION
ZOOM
CAMERA
TYPE OF LIGHTING
AUTO FOCUS
ZOOM LIMIT
ZOOM SPEED
LOW LIGHT LEVEL
IR CUT FILTER*
AUTO IR LEVEL*
<ADVANCED SETTINGS>
BACK
EXIT
PASSWORD
ENABLE PASSWORD
<EDIT PASSWORD>
BACK
EXIT
SET WASHER SEQUENCE
PRESET NOT DEFINED
<EDIT PRESET LABEL>
<EDIT PRESET SCENE>
<EDIT CAMERA SETTINGS>
WASHER TIME (SECS)
WIPER DELAY (SECS)
AUTO RETURN
<CLEAR PRESET>
<CLEAR CAMERA SETTINGS>
BACK
EXIT
EDIT DETECTION AREA*
DETECTION AREA 1
LOCATION
SENSITIVITY
DETECTION AREA 2
LOCATION
SENSITIVITY
DETECTION AREA 3
LOCATION
SENSITIVITY
DETECTION AREA 4
LOCATION
SENSITIVITY
BACK
EXIT
MOTION DETECTION*
MOTION DETECTION ENABLED
<EDIT DETECTION AREA>
ACTIVATE AUX
AUX TIME
BACK
EXIT
PRESETS
PRESET NUMBER
PRESET NOT DEFINED
<EDIT PRESET LABEL>
<EDIT PRESET SCENE>
<EDIT CAMERA SETTINGS>
<MOTION DETECTION>*
<CLEAR PRESETS>
<CLEAR CAMERA SETTINGS>
BACK
EXIT
WINDOW BLANKING
STYLE
BLANK ALL ABOVE
BLANK ALL BELOW
<SET WINDOWS>
BACK
EXIT
EDIT THE PASSWORD
- - - - - - - - - - - - - - - - -
1234567890 OK
ABCDEFGHIJ CANCEL
KLMNOPQRST
UZWXYZ.,-/ SPACE
abcdefghij BACKSPACE
klmnopqrst
uvwxyz*;:
* Available only with the 23X day/night camera.
** Available only with wiper models.