Vérification
✤ Pour résoudre un problème rencontré lors de l’utilisation de votre
caméscope, consultez le tableau ci-dessous.
✤ Si ces instructions ne vous permettent pas de résoudre le problème, notez:
■
la référence du modèle et le numéro de série indiqués sous le
caméscope,
■
votre numéro de garantie, si elle est toujours valable.
✤ Puis, contactez votre SAV ou le revendeur le plus proche.
Symptôme Explication/Solution
Vous ne pouvez pas ◆ Vérifiez le bloc batterie (voir page 18).
allumer le caméscope. ou l’adaptateur secteur. (voir page 17)
La touche ◆ Vérifiez que le commutateur principal est en
START/STOP ne position CAMERA.
fonctionne pas lors ◆ Vous avez atteint la fin de la cassette.
de l’enregistrement. ◆ Vérifiez la languette de protection sur la
cassette. (voir page 21)
Le caméscope s’éteint ◆ Vous avez laissé le caméscope sur
automatiquement. STANDBY pendant plus de 5 minutes
sans l’utiliser. (voir page 23)
◆ Le bloc batterie est complètement déchargé.
(voir page 20)
Le bloc batterie se ◆ La température ambiante est trop basse.
décharge rapidement. (voir page 20)
◆ Le bloc batterie n’a pas été complètement
rechargé. (voir page 18)
◆ Le bloc batterie n’est plus utilisable et ne
peut plus être rechargé. Utilisez un autre
bloc batterie.
Vous ne pouvez pas ◆ Le bloc batterie est complètement déchargé.
éjecter la cassette de ◆ Une erreur mécanique s’est peut-être
son compartiment. produite. (voir page 52)
La date et l’heure ◆ La pile au lithium n’est pas installée ou
clignotent plus de 2 fois est complètement déchargée. (voir page 16)
en mode Caméscope.
ENGLISH FRANÇAIS
53
Troubleshooting
Checking
✤ If you run into any problem using the camcorder, use the following
table to troubleshoot the problem.
✤ If these instructions do not allow you to solve the problem,
take a note of:
■
The model and serial number marked on the bottom of the camcorder.
■
Your warranty, if applicable.
✤ Then contact your nearest authorized service center.
Symptom Explanation/Solution
You cannot switch the ◆ Check the battery pack (see page 18)
camcorder on. or the AC power adapter. (see page 17)
Start/Stop does not ◆ Check the POWER, set it to CAMERA.
operate while
recording.
◆ You have reached the end of the cassette.
◆ Check the record protection tab on the cassette.
(see page 21)
The camcorder goes ◆ You have left the camcorder set to STANDBY
off automatically. for more than 5 minutes without using it.
(see page 23)
◆ The battery pack is fully used up.(see page 20)
The battery pack is ◆ The atmospheric temperature is too low.
quickly exhausted. (see page 20)
◆ The battery pack has not been charged fully.
(see page 18)
◆ The battery pack is completely dead, and
cannot be recharged. Use another battery pack.
You cannot eject the ◆ The battery pack is fully used up.
cassette from the ◆ A mechanical fault might have occurred.
compartment. (see page 52)
The DATE/TIME indicator ◆ The lithium battery is not installed or is
flashes more than 2 times fully used up. (see page 16)
when you set the
camcorder to CAMERA.
The playback picture ◆ The video heads might be dirty. (see page 50)
is poor.
You cannot operate any
◆
A mechanical fault might have occurred
.
functions on the camcorder.
(see page 52)
Dépannage