Sanyo VCC-MD300 Security Camera User Manual


 
− 9 −
Message
Backlight BLC OFF A0 06 00 CS FF Backlight compensation OFF
Multi BLC ON A0 06 01 CS FF Backlight compensation multifractionated evaluative metering mode (Backlight compensates after
measuring the light of the entire screen.)
Multi BLC Weight - A0 06 04 00 CS FF Sensitivity settings during Multi BLC
BLC is easier to determine with a larger value (Initial value: 7)
Multi BLC Weight + A0 06 04 01 CS FF
Multi BLC Weight Preset A0 06 05 CS FF Returns sensitivity during Multi BLC to factory defaults (Initial value: 7)
Multi BLC Weight Direct A0 06 06 0p CS FF p: Direct sensitivity settings 0-15 during Multi BLC (Initial value: 7)
Multi BLC Bright - A0 06 07 00 CS FF Brightness settings during Multi BLC
Larger value increases brightness when determining BLC (Initial value: 7)
Multi BLC Bright + A0 06 07 01 CS FF
Multi BLC Bright Preset A0 06 08 CS FF Returns brightness settings during Multi BLC to factory defaults (Initial value: 7)
Multi BLC Bright Direct A0 06 09 0p CS FF p: Direct brightness settings 0-15 during Multi BLC (Initial value: 7)
Center BLC ON A0 06 0B CS FF BLC center-weighted metering mode (Backlight compensates after measuring the light mainly in the
center.)
Center BLC Weight Preset A0 06 0F CS FF Returns sensitivity settings during Center BLC to factory defaults (Each initial value: 0)
* Therefore, Center is always 7
Center BLC Weight Direct A0 06 10 0p 0q 0r 0s CS FF Sensitivity settings during Center BLC
p: Top(0-7) q: Bottom(0-7) r: Left(0-7) s: Right(0-7) (Each initial value: 0)
Center BLC Area Preset A0 06 12 CS FF
Returns center area settings during Center BLC to factory defaults
(Each initial value: 0)
Center BLC Area Direct A0 06 13 0p 0q 0r 0s CS FF Center area settings during Center BLC
p: x-position(0-7) q: y-position(0-5) r: x-size(0-7) s: y-size(0-5)
(Initial value: x-position: 2 y-position: 1 x-size: 3 y-size: 3)
*When x-size:0 y-size:0, it becomes 1 area.
Center BLC Area Display A0 06 14 0p 0q CS FF Displays the Center BLC Area settings status on the monitor. p: Display (0: OFF, 1: ON),
q: Displayed area
(
0: CENTER, 1: TOP, 2: BOTTOM, 3: LEFT, 4: RIGHT)
* The area that is not covered with zebra markings shows the setting area.
Mask BLC ON A0 06 15 CS FF BLC mask mode (Backlight compensates after measuring the light, ignoring areas set as mask.)
Mask BLC Area Preset A0 06 19 CS FF Return mask area settings during Mask BLC to factory defaults
Mask BLC Area Direct A0 06 1D 0p 0q 0r 0s 0t 0u Mask area settings during Mask BLC (Note 1)
0v 0w 0x 0y 0z 0n CS FF
BLC ON A0 06 33 CS FF Returns to the mode before BLC OFF only when BLC OFF
BLC Mask Display A0 06 1E 0p CS FF p: Displays the BLC MASK settings status on the monitor.
(
1: ON/0: OFF
)
Shutter
Speed
Shutter Speed + A0 07 0B CS FF Increases shutter speed by one notch (Long time mode x 32 – High speed mode 1/10000) (Note 3)
Shutter Speed - A0 07 0C CS FF Decreases shutter speed by one notch (Long time mode x 32 – High speed mode 1/10000) (Note 3)
Shutter Speed Set long A0 07 0E 0p CS FF Shutter Speed Mode Settings (Note 3)
0: Prolonged exposure shutter mode, 1: Normal mode, 3: High speed shutter mode
Shutter Speed OFF A0 07 0F CS FF Returns the shutter speed mode setting to normal mode setting
Shutter Long Direct A0 07 11 0p CS FF Shutter speed settings during prolonged exposure shutter mode
(0: x1, 1: x2, 2: x4, 3: x8, 4: x16, 5: x32)
Shutter Short Direct A0 07 12 0p CS FF Shutter speed settings during high speed shutter mode
The numbers within the brackets refer to the PAL model
(0: 1/60 [1/50], 1:1/100 [1/120], 2: 1/250, 3: 1/500, 4: 1/1000, 5: 1/2000, 6: 1/4000, 7: 1/10000)
Sense Up + A0 07 1A CS FF Increase electronic sensitivity settings (Note 3)
Sense Up - A0 07 1B CS FF
Sense Up Direct A0 07 1D 0p CS FF p: Direct increased electronic sensitivity settings (Note 3)
(0: OFF, 1: x2, 2: x4, 3: x8, 4: x16, 5: x32)
ELS OFF A0 07 28 CS FF Sets shutter speed to 1x (1/60 [1/50]) after saving
The numbers within the brackets refer to the PAL model
ELS ON A0 07 29 CS FF Returns to electronic shutter speed saved by ELS OFF
Motion
Detector
Motion Detector OFF A0 08 00 CS FF
Motion sensor ON/OFF (Note 3)
Motion Detector ON A0 08 01 CS FF
Motion Size Preset A0 08 05 CS FF Returns detected motion size settings to factory defaults (Initial value: V-Size: 1, H-Size: 1)
Motion Size Direct A0 08 06 0p 0q CS FF Detected motion size settings p: V-Size (1-6) q: H-Size (1-8)
但し、
VxH
MAX 9 (Initial value: V-Size:
1, H-Size: 1)
Motion Size Display A0 08 07 0p CS FF p: Displays the MOTION SIZE settings status on the monitor. (1: ON/0: OFF)
Masking OFF A0 08 0A CS FF
Mask area settings for motion detection ON/OFF
Masking ON A0 08 0B CS FF
Mask Area Preset A0 08 0F CS FF Returns mask area for motion detection to factory defaults
Mask Area Direct A0 08 13 0p 0q 0r 0s 0t 0u Mask area settings for motion detection (Note 1)
0v 0w 0x 0y 0z 0n CS FF
Motion Mask Display A0 08 14 0p CS FF p: Displays the MOTION MASK settings status on the monitor. (1: ON/0: OFF)
Sensitivity Move + A0 08 15 CS FF
Motion detection sensitivity settings (Initial value: 5)
* Smaller values increase the sensitivity to small movements.
Sensitivity Move - A0 08 16 CS FF
Sensitivity Move Preset A0 08 19 CS FF Returns motion detection sensitivity settings to factory defaults (Initial value: 5)
Sensitivity Move Direct A0 08 1D 0p CS FF p: Direct motion detection sensitivity settings 1-10 (Initial value: 5)
Sensitivity Y-Level + A0 08 1F CS FF
Minimum brightness settings for motion detection (Initial value: 5)
* Smaller values increase the sensitivity to movements even on dark screens.
Sensitivity Y-Level - A0 08 20 CS FF
Sensitivity Y-Level Peset A0 08 23 CS FF Returns minimum brightness settings for motion detection to factory default (Initial value: 5)
Sensitivity Y-Level Direct A0 08 27 0p CS FF p: Direct minimum brightness settings for motion detection 1-10 (Initial value: 5)
Sensitivity Y-Differ + A0 08 29 CS FF
Brightness variation settings for undetected motion (Initial value: 5)
* Smaller values increase the sensitivity to movements even with large brightness variation.
Sensitivity Y-Differ - A0 08 2A CS FF
Sensitivity Y-Differ Preset A0 08 2D CS FF Returns brightness variation settings for undetected motion to factory defaults (Initial value: 5)
Sensitivity Y-Differ Direct A0 08 31 0p CS FF p: Direct brightness variation settings for undetected motion 1-10 (Initial value: 5)
Sensitivity Duration + A0 08 33 CS FF
Continuous movement time for motion detection (Initial value: 1)
* Smaller values increase the sensitivity to fast moving subjects.
Sensitivity Duration - A0 08 34 CS FF
Sensitivity Duration Preset A0 08 37 CS FF Returns continuous movement time for motion detection to factory defaults (Initial value: 1)
Sensitivity Duration Direct A0 08 3B p CS FF p: Direct continuous movement time for motion detection 1-60 (Initial value: 1)
Motion Zoom A0 08 3D 0p CS FF p: Zoom magnification during motion detection (Initial value: 0)
(0: OFF, 1: x1.4, 2: x2, 3: x2.8, 4: x4, 5: x5.6, 6: x 1/1.4, 7: x 1/2, 8: x 1/2.8, 9: x 1/4, 10: x 1/5.6)
Motion Interval A0 08 42 0p CS FF p: Interval time until the start of next detection during motion detection (Initial value: 0)
(0: 5s, 1: 10s, 2: 15s, 3: 20s, 4: 30s, 5: 1m, 6: 2m, 7: 3m, 8: 4m, 9: 5m)
Communications Protocol
Model: VCC-MD800/700/600/500
CS: Checksum
FF: Terminator