Filter
Top Products
17
<<CHART
A
>>
Camera Lens Type Exp. Mode Metering TTL System Note Conf
Dist
D, G Type
All Modes All Modes
3-D Multi-Sensor
BL
AF lens other than
D, G type
All Modes All Modes Multi-Sensor BL
1
F5
F100
F90X/N90ser.
F80/N80ser.
F70D/N70
F75/N75
Without Built in CPU
A/M
Modes
Center-weighted,
Spot Metering
Center Weighted /
Spot Fill-Flash
Can switch to TTL Mode. With
F5, F100, F80, series Cameras
spot metering system is always
TTL.
2
Matrix Pattern TTL BL
With Built-in CPU
All Modes
Center-weighted,
Spot Metering
Center Weighted /
Spot Fill-Flash
1
F4 Series
F-801S/N8008S
F-801/N8008
F65/N65
Pronea 600i
Without
Built-in CPU
A/M
Modes
Center-weighted,
Spot Metering
Center
Weighted/Spot
Fill-Flash
Can switch to TTL Mode. TTL BL
can work with only F4 series, AF
F3, Ai-S, Ai, Series E lens. Spot
metering system of F4 is always
TTL. Pronea 600i will be TTL,
when exposure mode is “M”.
Center Weighted BL cannot work.
2
Matrix Pattern TTL BL
With Built-in CPU
All Modes
Center-weighted,
Spot Metering
Center Weighted /
Spot Fill-Flash
F601/N6006
F-601M
Without
Built-in CPU
A/M
Modes
Center-weighted,
Spot Metering
Center Weighted /
Spot Fill-Flash
Spot Metering cannot use with
F-601M
2
With Built-in CPU
P/S
A/M
TTL BL
If exposure mode is “M”, it will be
Center Weighted/Spot Fill-Flash
2
F60D/N60
F50D/N50
F-401X/4004S
Without
Built-in CPU
M
Center Weighted /
Spot Fill-Flash
2
P TTL Programmed
Built-in CPU lens
,Ai-S, Ai, Series E,
AF F3 Lens
A/M TTL
F501/N2020
F301/N2000
Except above
lenses
A/M
TTL
2
P/S TTL Programmed
With Built-in CPU
A/M TTL
2
F401S/N4004S
F401/N4004
Without Built-in CPU
M
TTL
2
FA, FE2
FG, F3, FM3
With Built-in CPU;
Without Built-in CPU
A/M TTL
2
Confirm Distance:
1
: Flash’s LCD panel will show the F-number and working distance of flash automatically.
2
: Set the F-number on the flash to be the same as camera, and check the available working distance range on the
LCD panel. To set the F-number on the Flash, push the SEL button until the F-number blinks, and use + or – button
to set the F-number. Then press the SEL button again. The F-number will stop blinking.
When using Digital SLR cameras, functions will vary depending on the lens type and combinations of exposure
modes, same as F5 and F100 group (in chart A), however, they will use D-TTL (i-TTL).
LIMITS OF CONTINUOUS SHOOTING
To prevent overheating of the flash’s circuitry, do not use your Flash unit for at least 10minutes after
continiously using the flash as shown in the table below.
Mode Number of Flash Exposures
TTL, M(1/1,1/2) 15 Continuous Flash Shots
M(1/4, 1/8) 20 Continuous Flash Shots
M(1/16-1/32) 40 Continuous Flash Shots
Multi 10 Cycle
MANUAL FLASH OPERATION
Manual flash is provided for shooting subjects when the correct exposure
is difficult to obtain in the TTL mode. In the manual flash mode, you can
set the flash power level from 1/1 to 1/64 power in 1/3 stop increments.
1. Set the camera’s exposure mode (A, M modes).
2. Press the MODE button on the flash unit to select M.
3. Press the SEL button to make the guide number value blink.
4. Press
+
or
–
button to set the desired flash power output.
5.
To stop the manual flash output display blinking, Press the SEL button again.
6. When the Ready Light of the flash is illuminated, the unit is ready for use.