Filter
Top Products
15
05 BLK GAMMA
BLACK GAMMA
Off/On
[on]
Black gamma changes the initial slope of the gamma curve , only in the blacks.
BLK GAMMA RANGE
Low/l.mid/h.mid/high
[High]
MASTER BLK GAMMA -99 to 99 (0)
[22]
R BLK GAMMA -99 to 99 (0)
G BLK GAMMA -99 to 99 (0)
B BLK GAMMA -99 to 99 (0)
OUTPUT SELECT
Y/R/G/B
06 KNEE
KNEE
Off/on
Usually leave the knee switched on.
KNEE POINT 50 to 109 (95)
[50] 90
Sets where, as a percentage of the luminance scale, the knee starts to act.
KNEE SLOPE -99 to 99 (0)
[-136] -10
Sets how much compression is applied by the knee circuit.
KNEE SAT.
Off/on
[on]
Increases colour saturation in picture areas compressed by the knee, in proportion for RGB
KNEE SAT LEVEL -99 to 99 (0)
[70]
WHITE CLIP
Off/on
WHITE CLIP LEVEL 100.0 to 109.5 (105)
[109.5]
Normally set to about 104 for BBC / ITV preferred levels.
07 DETAIL 1
DETAIL
Off/on
APERTURE
Off/on
DETAIL LVL -99 to 99 (0)
-20 Factory setting of ‘0’ is a bit harsh. Normally turn down to between –20 and -30
APERTURE LVL 0 to 15 (0)
(don’t turn detail level below –70…it starts to look artificially soft.)
H/V RATIO -99 to 99 (0)
CRISPENING -99 to 99 (0)
LEVEL DEP
Off/on
LEVEL DEP LVL -99 to 99 (0)
DETAIL FREQ -99 to 99 (0)
08 DETAIL 2
KNEE APERTURE
Off
Knee aperture adds detail edges only to highlight areas compressed by the knee circuit.
KNEE APT LVL
0
DETAIL WHITE LIMIT
0
[-175]
Limits positive going (white halo) detail overshoots
DETAIL BLACK LIMIT
0
[-142]
Limits negative going detail overshoots
DETAIL V-BLK LIMIT
0
[34]
09 SD DETAIL
SD DETAIL
Off/on
There is a separate detail circuit for the down-converted SD output. Doesn’t affect recorded pictures.
SD DETAIL LVL -99 to 99 (0)
-10
SD CRISPENING -99 to 99 (0)
SD DETAIL WHITE LIMIT 0 to 15 (0)
SD DETAIL BLACK LIMIT -99 to 99 (0)
SD LEVEL DEP -99 to 99 (0)
SD LEVEL DEP LVL
Off/on
SD DETAIL FREQ -99 to 99 (0)
+50
SD H/V RATIO -99 to 99 (0)
10 SKIN DETAIL
SKIN DETAIL ALL
Off
Skin detail can key out a particular colour tone and reduce detail levels in that area.
SKIN DETECT
Position the on screen marker over the colour to be corrected and select the auto detect function.
SKIN AREA IND
Off
Displays a zebra type pattern over the areas selected for correction.
SKIN DTL SELECT
1
3 different settings can be remembered.
SKIN DETAIL
On
SKIN DTL LVL
0
Set the amount of detail to be removed (or added) here.
SKIN DTL SAT
0
Manually select the colour saturation to be targeted.
SKIN DTL HUE
0
Manually select the colour hue to be targeted.
SKIN DTL WIDTH
40
Manually select the width of the range of colours to be targeted.
11 LINEAR MATRIX
MATRIX
Off/on
MATRIX ( USER)
Off/on
[On]
MATRIX (PRESET)
Off/on
[Off] On
MATRIX ( PRST SEL)
1-2-3-4-5-6
2
1 SMPTE-240M, 2 ITU-709, 3 SMPTE Wide, 4 NTSC ,5 EBU, 6 ITU-609
MATRIX ( USER) R-G -99 to 99 (0)
[-53]
MATRIX ( USER) R-B -99 to 99 (0)
[0]
MATRIX ( USER) G-R -99 to 99 (0)
[-5]
MATRIX ( USER) G-B -99 to 99 (0)
[-6]
MATRIX ( USER) B-R -99 to 99 (0)
[-1]
MATRIX ( USER) B-G -99 to 99 (0)
[-9]
12 MULTI MATRIX
MATRIX
Off/on
.
MULTI MATRIX
Off/on
The multi-matrix can pick up on a particular colour in a scene and change its hue and saturation
AREA IND
Off/on
A zebra type pattern can be superimposed on targeted areas of colour
COLOUR DETECT
AXIS
B/B+/MG-/MG/ MG+/R/R+/YL-YL/YL+/G-/G/ /G+/CY/CY+/B-
HUE -99 to 99 (0)
SATURATION -99 to 99 (0)