Filter
Top Products
EPSON LQ-680Pro
14 - EPSON LQ-680Pro 11/00
8. Turn the ribbon-tightening knob again to remove any slack
in the ribbon and to make sure the ribbon moves freely.
9. Close the printer cover.
The printer pauses and cannot print when the printer
cover is open.
Changing the Default Settings
While you can often set the default settings through your
application software or printer driver, you may need to change a
default setting from the printer’s control panel using the default
setting mode. The table below lists the default settings (in bold)
and options you can select in this mode.
* These settings take effect only when IBM 2390 Plus emulation is
selected.
Follow the steps below to enter the default setting mode and
change the printer’s default settings.
To print all the instructions, you need 5 sheets of letter-
or A4-size single-sheet paper or 5 pages of continuous
paper. If you use single sheets without a cut-sheet
feeder, you need to load a new sheet each time the
printer ejects a printed sheet.
1. Make sure paper is loaded and the printer is turned off.
Whenever you turn off the printer, wait at least 5
seconds before turning it back on; otherwise you may
damage the printer.
2. While holding down the Font button, turn on the printer.
The printer enters the default setting mode and prints the
language selection instructions.
3. If you need to select a different language, press the
Font
button until the
Font lights indicate the language you want,
as described in the language selection instructions.
4. Press the
Tear Off/Special Paper button to confirm your
language selection and print the current default settings.
5. If you do not need to change any settings, go to step 6.
If you want to change any of the default settings, press the
Tear Off button to print the instructions (three pages) in
the language you selected.
Follow these instructions to change the default settings
using the buttons on the printer’s control panel.
Settings Options
Page length for tractor Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8,
8.5,
11
, 70/6, 12, 14, 17
Skip over perforation On,
Off
Auto tear-off On,
Off
Auto line feed On,
Off
Print direction
Bi-D
, Uni-D, Auto
Software
ESC/P2
, IBM 2390 Plus
0 slash
0
,
High speed draft
On
, Off
I/F mode
Auto
, Parallel, Optional
Auto I/F wait time
10 seconds
, 30 seconds
Parallel I/F bidirectional mode
On
, Off
Packet mode
Auto
, Off
Auto CR (IBM 2390 Plus)* On,
Off
A.G.M. (IBM 2390 Plus)* On,
Off
0
Character table* Standard model:
Italic,
PC 437
, PC 850, PC 860,
PC 863, PC 865, PC 861, BRASCII,
Abicomp, Roman 8, ISO Latin 1,
PC 858, ISO 8859-15,
All other models: Italic, PC 437,
PC 850, PC 437 Greek, PC 853,
PC 855, PC 852, PC 857, PC 864,
PC 866, PC 869, MAZOWIA,
Code MJK, ISO 8859-7, ISO Latin 1T,
Bulgaria, PC 774, Estonia,
ISO 8859-2, PC 866 LAT, PC 866 UKR,
PC APTEC, PC 708, PC 720,
PC AR864, PC 860, PC863, PC 865,
PC 861, BRASCII, Abicomp,
Roman 8, ISO Latin 1, PC 858,
ISO 8859-15, PC 771
International character set for
Italic table
Italic U.S.A
., Italic France, Italic
Germany, Italic U.K., Italic Denmark1,
Italic Sweden, Italic Italy, Italic Spain1
Font OCR-B, Orator, Orator-S, Script C,
Roman T
, Sans Serif H
Manual feed wait time 0.5 second,
1 second
, 1.5 seconds,
2 seconds
Buzzer
On
, Off
Overlapping forms On,
Off
Settings Options