Filter
Top Products
Others
45
LSQT1284
2:The remaining tape time indication
disappears.
• The remaining tape time indication may
disappear temporarily during frame-by-frame
playback or other operation. If you continue
ordinary recording or playback, the indication is
restored.
3:The remaining tape time Indication does not
match the actual remaining tape time.
• If scenes of less than 15 seconds are
continuously recorded, the remaining tape time
cannot be correctly displayed.
• In some cases, the remaining tape time
indication may show remaining tape time that is
2 to 3 minutes shorter than the actual
remaining tape time.
4:The function indications such as the mode
indication or the remaining tape time
indication are not shown.
• If you set [SETUP] >> [DISPLAY] >> [OFF], all
indications other than the tape running
condition, warning, and date are not displayed.
Playback (Sound)
1:Sound is not played back from the built-in
speaker of the Camcorder.
0 Is the volume too low? During playback, push
the [sVOLr] lever to display the volume
indication and adjust it. (
-35-)
2:Different sounds are reproduced at the
same time.
• Have you set [SETUP] >> [AUDIO OUT] >>
[STEREO] and reproduced a picture containing
the main sound and sub sound? Set to [L] to
hear main sound, and set to [R] to hear the sub
sound. (
-41-)
Playback (Pictures)
1: Although the Camcorder is correctly connected
to a TV, playback images cannot be seen.
The playback images are vertical.
• Have you selected video input on the TV?
Please read the operating instructions of your
TV and select the channel that matches the
input terminals used for the connection.
• Is the [TV ASPECT] setting correct? Change
the setting to match the aspect ratio of the TV.
[SETUP] >> [TV ASPECT] >> [16:9] or [4:3].
2:Mosaic-pattern noise appears on images
during cue or review playback.
• This phenomenon is characteristic of digital
video systems. It is not a malfunction.
3:Horizontal stripes appear on images during
cue and review playback.
• Horizontal stripes may appear depending on
the scene, but this is not a malfunction.
4:Playback picture is not clear.
• Are the heads of the Camcorder dirty? If the
heads are dirty, playback image cannot be
clear. Clean the heads by using the head
cleaner for digital video (optional). (
-46-)
• If the terminal for the AV cable is soiled, noises
may appear on the screen. Wipe the soil off the
terminal with a soft cloth, and then connect the
cable to the A/V terminal.
• Is a picture containing a copyright protection
signal (copy guard) being recorded? When a
protected picture is played back by the
Camcorder, mosaic-like patterns appear on the
picture.
Others
1:The indication disappears, the screen is
frozen, or no operation can be performed.
• Turn off the power to the Camcorder. If the
power cannot be turned off, press the [RESET]
button, or detach the battery or AC adaptor and
then reattach it. Turn on the power again. If
normal operation is still not restored, detach the
power connected, and contact Panasonic. (
-55-)
2:“PUSH THE RESET SWITCH” is displayed.
• An irregularity in the Camcorder has been
automatically detected. Remove the cassette
for data protection and then press the [RESET]
button with the boss A. The Camcorder will be
activated.
• If you do not press the [RESET] button, the
power to the Camcorder is turned off
automatically about 1 minute later.
• Even after you press the [RESET] button, the
indication may still appear repeatedly. If so, the
Camcorder needs repair. Detach the power
connected, and contact Panasonic. (
-55-)
A
RESET
PV-GS90P_LSQT1284_Eng.book 45 ページ ２００７年１１月２８日 水曜日 午前９時２０分