Filter
Top Products
16 Pelco Manual C416M-C (1/98)
Table A. DD08 Series Dome Drive Exploded Assembly Parts List (Mechanical)
Item Quantity Description Part Number
1 2 Bushing 80010004
2 2 Push nut 80010011
3 1 Upper drive mount bracket 8004034COMP
4 2 Dome drive latch pin 8004145COMP
5 1 Slip ring, 10-lead SR10-1
6 1 Spindle 8004004COMP
7 3 Pan limit stop (except DD08E3L model) 80010050
8 1 25-position connector receptacle CON10J025Z41T
9 1 Pan limit pin bracket (except DD08E3L model) 8004013COMP
10 1 Pan gear 80010012
11 4 Thrust washer 90010002
12 2 Thrust bearing 90010001
13 1 Bronze bearing 90010029
14 1 Pan bearing boss 8004002COMP
15 1 PC board assy, backplane *
16 1 PC board assy, power supply *
17 1 PC board assy, CPU *
18 1 PC board assy, video processor *
19 1 Receiver/driver cover 8004010COMP
20 1 Bracket, receiver PCB guides 8004009COMP
21 1 Dome drive frame 8081000WA
22 1 Tilt gear 80010013
23 1 Tilt shaft 8004018COMP
24 1 Quick connect for lens 8004062COMP
25 1 Grommet (except DD08E3L model) GRO2172N
26 6 PC board guides MMS300-4.25
27 1 Bracket, receiver PC board guide 8004008COMP
28 2 Motor gear 80010101
29 1 Pan spindle nut 9004004COMP
30 1 Gear, preset, pan spindle (except DD08C2L model) 8004006COMP
31 1 Dome bracket 8084001COMP
32 1 ABS dome liner 80810009
33 2 Ball stud PT180410000
34 2 Ball stud receiver PT180410001
35 Switch, with actuator: SWI111SM1
2 DD08E3L (tilt only)
4 DD08C2L and DD08E2L (pan and tilt)
36 1 Wire fatigue clamp 80010016
37 1 Shipping stabilizer bracket (** REMOVE BEFORE OPERATING **) 8084203COMP
38 1 Tilt motor:
Stepper, DC, vari-speed, type 3 drive 8008000
24 VAC, 14 rpm, w/gearhead, type 2 drive 8008214
39 1 Pan limit pin (except DD083EL model) 8004011COMP
40 2 Sealed bearing 80010000
41 1 Wave spring 80010002
42 1 Boss, bearing, tilt 8004000COMP
43 1 Encoder, preset tilt (except DD08C2L) ENCS1-512
44 1 Gear, preset tilt (except DD08C2L) 28010017
45 1 Encoder, preset pan (except DD08C2L) ENCS1-512I
46 1 Bracket, pan preset encoder (except DD08C2L) 8004012COMP
47 1 Gear, pan preset encoder (except DD08C2L) PT250010002
48 2 Snap ring (except DD08E3L) 15510000
49 1 Pan motor:
Stepper, DC, vari-speed, type 3 drive 8008000
24VAC, 48 rpm, w/gearhead, type 2 drive 8008248
53 1 Shim, 3/8" ID x 5/8" OD x .047 thick ZHSHIM.047
54 3 Spindle standoff 8004123COMP
55 Spacer:
1 Motor, tilt, vari-speed (not shown) 8084003COMP
1 Motor, tilt, AC (not shown) 8084002COMP
* Refer to dome receiver/driver manual for part number.